Home › Drivetrain › EA67F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE SYSTEM › from 2020.09
RM36W0E _52 Drivetrain _095283 EA67F MANUAL TRANSMISSION / TRANSAXLE _0448030 MANUAL TRANSAXLE SYSTEM C

EA67F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE SYSTEM  P080512  Clutch Position Sensor "A"Circuit Short to Battery  P080514  Clutch Position Sensor "A"Circuit Short to Ground or Open  


DESCRIPTION

The clutch pedal stroke sensor assembly is mounted on the clutch pedal, and detects the clutch pedal position and sends signals to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P080512 Clutch Position Sensor "A"Circuit Short to Battery Clutch stroke sensor signal voltage is 4.8 V or more for 0.5 seconds or more (1 trip detection logic)
·

Clutch pedal stroke sensor assembly

·

Open or short in clutch stroke sensor circuit

·

ECM


Does not come on DTC stored SAE Code:
P0808
P080514 Clutch Position Sensor "A"Circuit Short to Ground or Open Clutch stroke sensor signal voltage is 0.2 V or less for 0.5 seconds or more (1 trip detection logic)
·

Clutch pedal stroke sensor assembly

·

Open or short in clutch stroke sensor circuit

·

ECM


Does not come on DTC stored SAE Code:
P0807

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

Turn the ignition switch to ON and wait for 3 seconds or more.

4.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

5.

Input the DTC: P080512 or P080514.

6.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C364959E11
0.927,3.677 3.99,3.875 3.063,0.198 10 false Clutch Pedal Stroke Sensor Assembly 0.938,3.438 1.396,3.635 0.458,0.198 10 false A107 5.344,4.052 5.802,4.25 0.458,0.198 10 false A106 5.344,4.26 5.802,4.458 0.458,0.198 10 false ECM 5.177,1.833 5.792,2.031 0.615,0.198 10 false VCCL 5.177,2.292 5.635,2.49 0.458,0.198 10 false CLS 5.177,2.75 5.792,2.948 0.615,0.198 10 false E2CL 5.927,1.667 6.385,1.865 0.458,0.198 10 false 5 V 1.844,1.833 2.302,2.031 0.458,0.198 10 false VDD 1.833,2.292 2.292,2.49 0.458,0.198 10 false OUT 1.833,2.74 2.292,2.938 0.458,0.198 10 false GND 4.844,1.833 5.156,2.031 0.313,0.198 10 false 43 4.844,2.292 5.302,2.49 0.458,0.198 10 false 52 4.854,2.74 5.167,2.938 0.313,0.198 10 false 44 2.271,1.833 2.427,2.031 0.156,0.198 10 false 3 2.271,2.292 2.427,2.49 0.156,0.198 10 false 2 2.26,2.74 2.417,2.938 0.156,0.198 10 false 1

PROCEDURE

1.READ VALUE USING GTS (CLUTCH STROKE SENSOR VOLTAGE)
a.

Enter the following menus.

Powertrain > Engine > Data List
Tester Display
Clutch Stroke Sensor Voltage
50003 372 607

b.

Read the values displayed on the GTS.

Standard Voltage:
GTS Display Condition Specified Condition
CLUTCH STROKE SENSOR VOLTAGE Clutch pedal fully released 0.5 to 1.1 V
Clutch pedal fully depressed 2.6 to 4.5 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CLUTCH PEDAL STROKE SENSOR ASSEMBLY)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CLUTCH PEDAL STROKE SENSOR ASSEMBLY)
a.
C364961C08
1.417,0.177 1.917,0.417 0.5,0.24 1.406,1.104 1.083,1.667 true 1.667,1.094 2.167,1.667 true 1.521,0.219 1.979,0.417 0.458,0.198 10 false A107 0.75,1.604 1.208,1.802 0.458,0.198 10 false GND 2.24,1.625 2.698,1.823 0.458,0.198 10 false VDD 0.073,0.094 0.385,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Clutch Pedal Stroke Sensor Assembly)


Disconnect the clutch pedal stroke sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A107-3 (VDD) - A107-1 (GND) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL STROKE SENSOR ASSEMBLY - ECM)

NG

6.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL STROKE SENSOR ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL STROKE SENSOR ASSEMBLY - ECM)
a.

Disconnect the A106 ECM connector.


b.

Disconnect the A107 clutch pedal stroke sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A107-2 (OUT) - A106-52 (CLS) Always Below 1 Ω
A106-52 (CLS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE CLUTCH PEDAL STROKE SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE CLUTCH PEDAL STROKE SENSOR ASSEMBLY
a.

Replace the clutch pedal stroke sensor assembly.



Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P080512 OR P080514)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P080512 OR P080514)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

i.

Read the DTCs.


Result:
Result Proceed to
DTC is not output A
DTC P080512 or P080514 is output B



A

END

B

6.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL STROKE SENSOR ASSEMBLY - ECM)
a.

Disconnect the A106 ECM connector.


b.

Disconnect the A107 clutch pedal stroke sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A107-1 (GND) - A106-44 (E2CL) Always Below 1 Ω
A107-3 (VDD) - A106-43 (VCCL) Always Below 1 Ω
A106-44 (E2CL) - Body ground Always 10 kΩ or higher
A106-43 (VCCL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR