The manual transaxle oil temperature sensor (temperature sensor) installed inside the manual transaxle assembly detects the temperature of the fluid in the transaxle and outputs signals to the ECM according to the fluid temperature.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P071011 | Transmission Fluid Temperature Sensor "A" Circuit Short To Ground | Manual transaxle oil temperature sensor (temperature sensor) output voltage is less than 0.1 V (circuit shorted) for 5 seconds or more.
(1-trip detection logic) |
·
Wire harness or connector ·
Manual transaxle oil temperature sensor (temperature sensor) ·
ECM |
Does not come on | DTC stored | SAE Code:
P0712 |
When this DTC is output, check the manual transaxle oil temperature sensor (temperature sensor) in the Data List. Enter the following menus: Powertrain / Engine / Data List / M/T Oil Temperature.
| DTC No. | M/T Oil Temperature | Malfunction |
|---|---|---|
| P071011 | Higher than 135°C (284°F) | ·
Short to ground in THOM circuit |
If the Data List values are normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.
The ECM calculates the temperature of the MT fluid based on the voltage output by the manual transaxle oil temperature sensor (temperature sensor). If the output voltage of the manual transaxle oil temperature sensor (temperature sensor) is outside the normal range, there may be a malfunction in the manual transaxle oil temperature sensor (temperature sensor) or a short in the circuit. In that case, the ECM will illuminate the MIL and store a DTC.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and wait for 3 seconds or more.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P071011.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
Pre-procedure1
| *1 | Manual Transaxle Oil Temperature Sensor (Temperature Sensor) |
| *2 | ECM |
Disconnect the manual transaxle oil temperature sensor (temperature sensor) connector.
Procedure1
According to the display on the GTS, read the Data List.
| Tester Display |
|---|
| M/T Oil Temperature |
Post-procedure1
None.
| Result | Proceed to |
|---|---|
| The value of M/T Oil Temperature is -40°C (-40°F) | A |
| None of the above conditions are met | B |
A
Click hereDrivetrain>EA67F (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSAXLE OIL TEMPERATURE SENSOR>REMOVAL
B
Pre-procedure1
Disconnect the D104 ECM connector.
Disconnect the D100 manual transaxle oil temperature sensor (temperature sensor) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D104-104 (THOM) or D100-1 (THO) - Body ground and other terminals | Always | 10 kΩ or higher |
Post-procedure1
Connect the D100 manual transaxle oil temperature sensor (temperature sensor) sensor connector.
Connect the D104 ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG