Home › Drivetrain › EA67F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE SYSTEM › from 2020.09
RM36W0E _52 Drivetrain _095283 EA67F MANUAL TRANSMISSION / TRANSAXLE _0448030 MANUAL TRANSAXLE SYSTEM C

EA67F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE SYSTEM  P071512  Input/Turbine Speed Sensor "A" Circuit Short to Battery  P071514  Input/Turbine Speed Sensor "A" Circuit Short to Ground or Open  


DESCRIPTION

The transmission revolution sensor is mounted on the transaxle. The ECM calculates the transaxle input shaft speed using the sensor. When the input shaft rotates, the sensor generates a pulse signal and sends the signal to the ECM. The ECM calculates the input shaft speed based on the signal. If the input shaft speed falls below a threshold despite the engine running, the ECM interprets this as a malfunction in the transmission revolution sensor circuit. The ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P071512 Input/Turbine Speed Sensor "A" Circuit Short to Battery There is no malfunction in transmission revolution sensor (NIM) signals, and the transmission revolution sensor (NIM) output voltage is higher than 1.8 V for 2 seconds (1 trip detection logic).
·

Wire harness or connector

·

Transmission revolution sensor

·

ECM


Comes on DTC stored SAE Code:
P07C0
P071514 Input/Turbine Speed Sensor "A" Circuit Short to Ground or Open There is no malfunction in transmission revolution sensor (NIM) signals, and the transmission revolution sensor (NIM) output voltage is less than 0.2 V for 2 seconds (1 trip detection logic).
·

Wire harness or connector

·

Transmission revolution sensor

·

ECM


Comes on DTC stored SAE Code:
P07BF

MONITOR DESCRIPTION

The transmission revolution sensor (NIM) detects the rotation speed of the input shaft. Based on comparison with the transmission revolution sensor (NIM) (input shaft rotation speed), the ECM determines the necessary gear ratio. If the output shaft rotation speed deviates from the threshold value, the ECM determines that the transmission revolution sensor (NIM) is malfunctioning, and so the ECM will illuminate the MIL and store a DTC.

WIRING DIAGRAM

C318994E80
0.625,2.917 3.729,3.115 3.104,0.198 10 false Transmission Revolution Sensor 5.802,3.115 6.156,3.469 0.354,0.354 10 false ECM 5.677,1.177 6.135,1.375 0.458,0.198 10 false NIMB 5.417,1.177 5.875,1.375 0.458,0.198 10 false 53 2.073,1.177 2.531,1.375 0.458,0.198 10 false 2 1.635,1.167 2.094,1.365 0.458,0.198 10 false NIMB 1.625,2.146 2.083,2.344 0.458,0.198 10 false NIMO 2.073,2.146 2.531,2.344 0.458,0.198 10 false 1 5.417,2.125 5.875,2.323 0.458,0.198 10 false 54 5.677,2.125 6.135,2.323 0.458,0.198 10 false NIMO 5.802,2.938 6.26,3.135 0.458,0.198 10 false D105 0.646,2.688 1.104,2.885 0.458,0.198 10 false D99 6.313,0.969 6.771,1.167 0.458,0.198 10 false 12 V

CAUTION / NOTICE / HINT

CAUTION:
·
A371909

Strictly observe posted speed limits, traffic laws and road conditions.

·

Do not drive the vehicle with the cable of the GTS contacting the pedals, shift lever or steering wheel.

·

Driving the vehicle with the cable of the GTS contacting these areas could impede vehicle control, resulting in a serious accident.


·
A356953

Do not operate the GTS while driving the vehicle.

·

Operating the GTS while driving the vehicle will prevent you from paying sufficient attention to vehicle surroundings, and could result in a serious accident.



PROCEDURE

1.READ VALUE USING GTS (NIM SENSOR SPEED AND NIM SENSOR VOLTAGE)
a.

Enter the following menus.

Powertrain > Engine > Data List
Tester Display
NIM Sensor Speed
NIM Sensor Voltage
50003 372 539,882

b.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NIM Sensor Speed Input shaft speed (NIM) Min.: 0 rpm
Max.: 16383 rpm
Input shaft speed (NIM) equal to engine speed (NE): Clutch pedal not depressed, vehicle running Data is displayed in increments of 50 rpm.
NIM Sensor Voltage Transmission revolution sensor (NIM) output voltage Min.: 0.000 V
Max.: 4.999 V
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in Neutral) -

Result:
Result Proceed to
Data List value is not normal A
Data List value is normal B



A

2.INSPECT TRANSMISSION REVOLUTION SENSOR

B

2.INSPECT TRANSMISSION REVOLUTION SENSOR
a.

Remove the transmission revolution sensor.

Click hereDrivetrain>EA67F (MANUAL TRANSMISSION / TRANSAXLE)>SPEED SENSOR>REMOVAL


b.

Connect the battery to the transmission revolution sensor as shown in the illustration.

C277851C22
1.333,1.958 1.594,1.469 true 4.521,1.156 4.229,0.979 true 3.667,1.146 3.948,0.969 true 2.063,1.948 1.802,1.469 true 6.115,1.24 5.813,1.01 true 4.906,0.844 4.813,0.552 true 4.698,2.563 4.927,2.302 false 6.135,1.677 5.448,2.146 true 4.875,0.865 5.188,1.021 0.313,0.156 10 false *d 6.198,1.188 6.51,1.385 0.313,0.198 10 false *1 1,0.563 1.313,0.719 0.313,0.156 10 false *a 4.49,2.479 4.802,2.635 0.313,0.156 10 false *c 1.135,2 1.583,2.208 0.448,0.208 10 false NIMB 1.979,2.01 2.438,2.219 0.458,0.208 10 false NIMO 4.583,1.094 4.771,1.292 0.188,0.198 10 false 1 3.552,1.083 3.74,1.281 0.188,0.198 10 false 2 6.198,1.615 6.51,1.813 0.313,0.198 10 false *b
*1 Battery - -
*a Component without harness connected
(Transmission Revolution Sensor)
*b Magnet
*c 5 mm or less *d Ammeter



c.

Wave a magnetic object left and right 5 mm (0.197 in.) or less from the tip of the transmission revolution sensor to output a high/low signal while measuring the current.

NOTICE:

Make sure to wave the magnetic object during the inspection. The current will not change unless the magnetic object is moved as shown in the illustration.



d.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (NIMO) - 2 (NIMB) Low signal 4 to 8 mA
1 (NIMO) - 2 (NIMB) High signal 12 to 16 mA



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR - ECM)

NG

REPLACE TRANSMISSION REVOLUTION SENSOR

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR - ECM)
a.

Disconnect the D99 transmission revolution sensor connector.


b.

Disconnect the D105 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D99-1 (NIMO) - D105-54 (NIMO) Always Below 1 Ω
D99-2 (NIMB) - D105-53 (NIMB) Always Below 1 Ω
D99-1 (NIMO) or D105-54 (NIMO) - Body ground and other terminals Always 10 kΩ or higher
D99-2 (NIMB) or D105-53 (NIMB) - Body ground and other terminals Always 10 kΩ or higher



d.

Connect the D105 ECM connector.


e.

Connect the D99 transmission revolution sensor connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION REVOLUTION SENSOR - ECM)