Home › Engine / Hybrid System › G16E-GTS (FUEL) › FUEL SYSTEM › from 2020.09
RM36W0E _51 Engine / Hybrid System _095688 G16E-GTS FUEL _0449363 FUEL SYSTEM L

G16E-GTS FUEL  FUEL SYSTEM  PRECAUTION  


CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.

·
A357489

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.



BEFORE WORKING ON FUEL SYSTEM


a.

Before inspecting and repairing the fuel system, disconnect the cable from the negative (-) auxiliary battery terminal.

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY



b.

Do not smoke or work near fire when handling the fuel system.


c.

Keep fuel away from rubber or leather parts.



DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

Make sure the engine coolant temperature is 60°C (140°F) or less when performing this procedure.

·

Perform the following procedure to prevent fuel from spraying before removing any fuel system parts.

·

Pressure will still remain in the fuel lines even after performing the following procedure. When disconnecting a fuel line, cover it with a piece of cloth to prevent fuel from spraying or coming out.



a.

When discharging fuel system pressure by disconnecting the EFI MAIN NO. 2 relay:

i.

Remove the deck board assembly


ii.

Remove the deck floor box RH


iii.

Remove the deck floor box LH.


iv.

Remove the No.3 lower relay block cover.


v.

Remove the EFI MAIN NO. 2 relay.


vi.

Start the engine and stop it after 1 minute.


vii.
A476500

Disconnect the fuel pump assembly connector.


viii.

Start the engine. After the engine has stopped on its own, turn the ignition switch off.

NOTICE:

Do not increase the engine speed or drive the vehicle while waiting for the engine to stop on its own.



ix.

Crank the engine again and make sure that the engine does not start.

HINT:

DTC P008700 (Fuel Rail / System Pressure - Too Low) and P017100 (System Too Lean Bank 1) may be stored. Clear the DTCs before proceeding to the next step.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR



x.

Remove the fuel tank cap assembly and discharge the pressure from the fuel tank assembly.


xi.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>G16E-GTS AUXILIARY BATTERY>REMOVAL


xii.

Connect the fuel pump assembly connector.


xiii.

Install the EFI MAIN NO. 2 relay.


xiv.

Install the No.3 lower relay block cover.


xv.

Install the deck floor box LH.


xvi.

Install the deck floor box RH.


xvii.

Install the deck board assembly.



b.

When discharging fuel system pressure by disconnecting the fuel pump connector:

i.

Remove the bench type rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 3 Door)>REMOVAL


ii.

Remove the rear floor service hole cover.

Click hereEngine / Hybrid System>G16E-GTS (FUEL)>FUEL PUMP>REMOVAL


iii.
A472074

Disconnect the fuel suction tube with pump and gauge assembly connector.


iv.

Start the engine and stop it after 1 minute.


v.
A476500

Disconnect the fuel pump assembly connector.


vi.

Start the engine. After the engine has stopped on its own, turn the ignition switch off.

NOTICE:

Do not increase the engine speed or drive the vehicle while waiting for the engine to stop on its own.



vii.

Crank the engine again and make sure that the engine does not start.

HINT:

DTC P008700 (Fuel Rail / System Pressure - Too Low) and P017100 (System Too Lean Bank 1) may be stored. Clear the DTCs before proceeding to the next step.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR



viii.

Remove the fuel tank cap assembly and discharge the pressure from the fuel tank sub-assembly.


ix.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>G16E-GTS AUXILIARY BATTERY>REMOVAL


x.

Connect the fuel suction tube with pump and gauge assembly connector.


xi.

Connect the fuel pump assembly connector.


xii.

Install the rear floor service hole cover.

Click hereEngine / Hybrid System>G16E-GTS (FUEL)>FUEL PUMP>INSTALLATION


xiii.

Install the bench type rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 3 Door)>INSTALLATION




FUEL LINE


a.

When disconnecting a high-pressure fuel line, a large amount of fuel will spray. Perform the following procedure:

i.

Discharge fuel system pressure.


ii.

Disconnect the fuel tube.


iii.

Drain the fuel remaining inside the fuel tube into a container.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



b.

Quick Type A:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any dirt or foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A401631C04
0,0 0,0 false
V100135

Open
V100136

Pull


Clamp Type A (No. 1 Fuel Pipe Clamp):

Open the cover of the fuel pipe clamp and remove the fuel pipe clamp from the fuel tube connector.


ii.

Check that there is no dirt or other foreign matter around the fuel tube connector before disconnecting it. Clean the joint if necessary.


iii.
A403898C01
1.833,2.344 2.073,2.031 2.073,2.031 2.219,2.031 false 2.271,1.948 2.583,2.104 0.313,0.156 10 false *a
*a Retainer
V100135

Retainer Holding Position
V100136

Pull out


While holding the retainer at the positions shown in the illustration, pull up the retainer to disengage the lock claws.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



iv.
A403899C01
1.167,0.354 1.313,0.354 1.313,0.354 1.625,0.646 false 1.896,1.948 2.104,1.573 2.104,1.573 2.25,1.573 false 1.979,3.188 2.073,2.938 2.073,2.938 2.219,2.938 false 1.354,3.333 1.604,3.333 1.604,3.333 1.604,3.594 false 2.125,3.885 2.281,4.302 2.281,4.302 2.396,4.302 false 0.833,4.177 0.833,3.917 true 1.875,4.26 1.875,4.063 false 1.479,3.594 1.479,3.333 false 1,0.26 1.313,0.417 0.313,0.156 10 false *a 1.198,3.24 1.51,3.396 0.313,0.156 10 false *b 1.802,4.292 2.115,4.448 0.313,0.156 10 false *c 0.75,4.208 1.063,4.365 0.313,0.156 10 false *d 2.448,4.208 2.76,4.365 0.313,0.156 10 false *e 2.302,1.49 2.615,1.646 0.313,0.156 10 false *a 2.271,2.854 2.583,3.01 0.313,0.156 10 false *a
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Nylon Tube
*e Fuel Pipe
V100135

Retainer Holding Position
V100136

Pull out
V100137

Pull off


Pull up the retainer while holding it at the positions shown in the illustration and pull off the fuel tube connector.


v.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Do not bend, twist, pinch or kink the nylon tube.




vi.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


vii.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



c.

Quick Type A:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A393281C01
1.167,2.354 1.448,2.354 false 1,2.25 1.313,2.406 0.313,0.156 10 false *a
*a Retainer
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, push the fuel tube connector onto the fuel pipe, then push in the retainer to secure the connection.

NOTICE:

Confirm that the retainer makes a "click" sound when pushed.


HINT:

If it is difficult to push the fuel tube connector onto the fuel pipe, apply a small amount of clean gasoline to the tip of the fuel pipe.



ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.


iii.

Clamp Type A (No. 1 Fuel Pipe Clamp):

Install the EFI fuel pipe clamp to the fuel tube connector and close the cover of the EFI fuel pipe clamp.




d.

Quick Type B:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A297035C03
0.219,0.49 0.219,0.229 0.219,0.229 0.292,0.229 false 0.875,0.521 0.927,0.302 0.927,0.302 1,0.302 false 0.229,1.031 0.229,0.813 false 0.333,0.146 0.646,0.302 0.313,0.156 10 false *d 1.073,0.208 1.385,0.365 0.313,0.156 10 false *b 0.313,1.323 0.625,1.479 0.313,0.156 10 false *c 0.146,1.042 0.458,1.198 0.313,0.156 10 false *a
*a Fuel Tube Connector
*b Fuel Pipe
*c Retainer
*d O-ring
V100135

Pinch
V100136

Pull


Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has an O-ring that seals the pipe (fuel pipe).




iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



e.

Quick Type B:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A320802C01
1.729,1.396 1.885,1.594 0.156,0.198 10 false .
V100135

Pull


Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.


ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.




f.

Quick Type C:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.

Check if there is any foreign matter on the fuel pipe around the fuel tube connector before disconnecting it. Clean it if necessary.


ii.
A284031C06
1.896,2.24 2.052,2.24 2.052,2.24 2.313,2.396 false 1.885,3.146 2.042,3.146 2.042,3.146 2.354,2.875 false 1.708,2.177 2.094,2.406 0.385,0.229 10 *a 1.698,3.063 2.083,3.292 0.385,0.229 10 *b
*a Retainer
*b Claw
V100135

Pull
V100136

Pull


Pull the retainer to disengage the 2 claws and then pull the retainer up as shown in the illustration.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



iii.
A298118C01
2.292,1.052 2.49,1.313 0.198,0.26 10 .
V100135

Push
V100136

Pull


If the fuel tube connector and the fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



iv.

Check if there is any foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


v.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



g.

Quick Type C:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.

Check if there is any damage or foreign matter on the connecting parts of the fuel pipes.


ii.
A158187C11
2.552,2.865 2.167,2.865 false 2.229,2.073 2.5,2.25 false 1.969,2.771 2.271,3.031 0.302,0.26 10 *b 2.042,1.99 2.333,2.292 0.292,0.302 10 *a
*a Retainer
*b Claw
V100136

Push
V100135

Push In


Align the fuel tube connector with the fuel pipe, and them together until they are fully seated. Next, push the retainer into the fuel tube connector until its claws lock. If the fuel pipe is difficult to push into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe and reinsert it.


iii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.





FUEL INJECTOR ASSEMBLY


a.
A292669C01
0.125,0.125 3.292,1.313 3.167,1.188 0.125,1.458 3.302,3.208 3.177,1.75 1.302,1.135 1.302,1.021 false 0.854,1.135 0.854,0.875 false 0.875,2.719 0.875,2.406 false 1.323,2.708 1.323,2.563 false 0.771,1.146 1.083,1.302 0.313,0.156 10 *1 1.229,1.146 1.542,1.302 0.313,0.156 10 *2 0.219,0.198 0.531,0.354 0.313,0.156 10 *a 0.229,1.552 0.542,1.708 0.313,0.156 10 *b 1.271,2.771 1.583,2.927 0.313,0.156 10 *2 0.823,2.781 1.135,2.938 0.313,0.156 10 *1
*1 O-ring
*2 Fuel Delivery Pipe Sub-assembly
*a Correct
*b Incorrect


Observe the following precautions when removing and installing the fuel injector assemblies:

i.

Do not reuse the O-ring or injector vibration insulator.


ii.

When placing a new O-ring onto the fuel injector assembly, do not damage the O-ring.


iii.

Coat a new O-ring with gasoline or spindle oil before installing it.

NOTICE:

Do not use engine oil, gear oil or brake fluid.




b.
A213788C07
1.625,0.135 2.208,0.135 2.208,0.135 2.365,0.302 false 0.479,1.177 0.719,1.177 0.719,1.177 1.104,1.51 false 2.458,0.677 2.823,1.094 2.823,1.094 2.938,1.094 false 0.677,0.625 0.917,0.625 0.917,0.625 1.479,1.167 false 1.427,0.052 1.74,0.208 0.313,0.156 10 false *1 3.021,1.01 3.333,1.167 0.313,0.156 10 false *2 0.281,1.094 0.594,1.25 0.313,0.156 10 false *3 0.469,0.542 0.781,0.698 0.313,0.156 10 false *4
*1 Fuel Delivery Pipe Sub-assembly
*2 O-ring
*3 Injector Vibration Insulator
*4 Fuel Injector Assembly


Install the fuel injector assembly into the fuel delivery pipe sub-assembly and cylinder head sub-assembly as shown in the illustration.

NOTICE:

Apply gasoline or spindle oil to the contact surfaces of the fuel delivery pipe sub-assembly and fuel injector assembly before installing it.




FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY


NOTICE:
·
A472064C01
0.313,1.698 0.625,1.604 false 0.125,1.625 0.438,1.781 0.313,0.156 10 false *a
*a Tube


Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is pressed into the fuel suction plate sub-assembly.

·

When replacing the fuel filter, replace it together with the fuel suction plate sub-assembly.




INSPECT FOR FUEL LEAK


a.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs.

Click hereEngine / Hybrid System>G16E-GTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION