Home › Engine / Hybrid System › G16E-GTS (FUEL) › FUEL SENDER GAUGE ASSEMBLY › from 2020.09
RM36W0E _51 Engine / Hybrid System _095688 G16E-GTS FUEL _0449373 FUEL SENDER GAUGE ASSEMBLY A

G16E-GTS FUEL  FUEL SENDER GAUGE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel sender gauge assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 77020A 1.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 83320 2.REMOVE FUEL SENDER GAUGE ASSEMBLY

a.
A476562

Detach the 4 clamps and disconnect the wire harness.

NOTICE:
·

Do not damage the wire harness.

·

When disengaging each wire harness from the clamp, disengage one wire at a time.




b.
A476561

Disconnect the 2 connectors from the fuel suction plate sub-assembly.


c.
A476563

Detach the claw and remove the fuel sender gauge assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



Hide 58325E 3.REMOVE REAR FLOOR SERVICE HOLE COVER (for RH Side)

a.
A472009C01
1,0.521 0.604,0.844 true 0.417,0.75 0.615,0.938 0.198,0.188 10 true *a
*a Protective Tape


Remove the rear floor service hole cover and butyl tape.


b.
A472011

Disconnect the connector from the fuel tank vent tube assembly.


Hide 77285D 4.REMOVE NO. 1 FUEL TUBE CLAMP

Hide 77144 5.REMOVE FUEL PUMP GAUGE RETAINER

HINT:

Perform the same procedure as for the fuel suction tube with pump and gauge assembly.

Click hereEngine / Hybrid System>G16E-GTS (FUEL)>FUEL PUMP>REMOVAL


Hide 77010 6.REMOVE FUEL TANK VENT TUBE ASSEMBLY

a.
A472015

Disconnect the fuel return vent tube sub-assembly and remove the fuel tank vent tube assembly from the fuel tank assembly.

Click hereEngine / Hybrid System>G16E-GTS (FUEL)>FUEL SYSTEM>PRECAUTION

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



b.
A472017

Remove the gasket from the fuel tank assembly.


Hide 83320B 7.REMOVE NO. 2 FUEL SENDER GAUGE ASSEMBLY

a.
A476564

Disconnect the connector from the fuel tank vent tube assembly.


b.

Detach the 2 clamps and disconnect the wire harness from the fuel tank vent tube assembly.

NOTICE:

Do not damage the wire harness.



c.
A476565

Detach the claw and remove the No. 2 fuel sender gauge assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.