87220
1.INSTALL AIR DUCT ASSEMBLY
Install the air duct assembly with the 2 nuts.
Install the front panel silencer with the 3 retainers as shown in the illustration.
88625
2.INSTALL NO. 1 COOLER THERMISTOR
88501
3.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
Install the No. 1 cooler evaporator sub-assembly with No. 1 cooler thermistor to the upper heater case.
Engage the guides and claws to install the upper heater case with No. 1 cooler evaporator sub-assembly.
Install the 2 screws.
| *a | Clamp |
| *b | Guide |
Engage the guides and clamp.
87107A
4.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY
Install the heater radiator unit sub-assembly as shown in the illustration.
87124B
5.INSTALL HEATER CLAMP
Engage the claws to install the heater clamp.
87114B
6.INSTALL HEATER COVER
Install the heater cover with the screw.
55909A
7.INSTALL AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)
| *a | MAX COLD |
| *b | MAX WARM |
Set the cable gear and unit gear to the MAX COLD position.
Engage the guides and claws to install the air mix damper control cable sub-assembly.
55906A
8.INSTALL DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)
| *a | FACE |
| *b | 45° |
Set the cable gear and unit link to the FACE position.
Engage the guides and claws to install the defroster damper control cable sub-assembly.
87050C
9.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)
Move the gear of the air conditioner radiator assembly so that the shape of the center gear portion of the air conditioner radiator assembly is aligned with the sensor shaft and output shaft of the No. 1 air conditioning radiator damper servo sub-assembly, and temporarily install the No. 1 air conditioning radiator damper servo sub-assembly as shown in the illustration.
| *a | Align shapes | - | - |
Install the No. 1 air conditioning radiator damper servo sub-assembly with the 3 screws.
87130D
10.INSTALL BLOWER ASSEMBLY
82143C
11.INSTALL NO. 3 INSTRUMENT PANEL WIRE (for Cold Area Specification Vehicles)
88650N
12.INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY (except G16E-GTS)
Engage the guide to temporarily install the air conditioning amplifier assembly as shown in the illustration.
Install the air conditioning amplifier assembly with the screw.
88650N
13.INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY (for G16E-GTS)
Engage the guide to install the air conditioning amplifier assembly.
Install the air conditioning amplifier assembly with the 2 screws.
82210K
14.INSTALL AIR CONDITIONING HARNESS ASSEMBLY
for Automatic Air Conditioning System:
Engage the guides.
Connect 4 connectors to install the air conditioning harness assembly.
for Manual Air Conditioning System Dual Layer Type:
Engage guides.
Connect the connector to install the air conditioning harness assembly.
88539J
15.INSTALL DRAIN COOLER HOSE
| *a | Rib |
| *b | Hose Notch |
Align the hose notch with the rib as shown in the illustration and install the drain cooler hose.
87114L
16.INSTALL NO. 2 HEATER COVER (except Cold Area Specification Vehicles)
Engage the claws to install the No. 2 heater cover.
87212K
17.INSTALL NO. 6 REAR AIR DUCT (for Cold Area Specification Vehicles)
Engage the claws to install the No. 6 rear air duct.
87211A
18.INSTALL NO. 2 AIR DUCT
Engage the claws to install the No. 2 air duct.
Install the screw.
88897P
19.INSTALL ASPIRATOR
Engage the claws and guide to install the aspirator.
88515
20.INSTALL COOLER EXPANSION VALVE
Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the No. 1 cooler evaporator sub-assembly.
for Gasoline Model (for HFC-134a(R134a)):
ND-OIL 8 or equivalent
for Gasoline Model (for HFO-1234yf(R1234yf)):
ND-OIL 12 or equivalent
for HV Model:
ND-OIL 11 or equivalent
Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.
Keep the O-rings and O-ring fitting surfaces free of foreign matter.
Using a 4 mm hexagon socket wrench, install the cooler expansion valve with the 2 hexagon bolts.
88897K
21.INSTALL COOLER PIPE GROMMET
Install the cooler pipe grommet.
55990B
22.INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY
Engage the guides and claws to install the lower defroster nozzle assembly.