Home › Drivetrain › EA67F (MANUAL TRANSMISSION / TRANSAXLE) › SHIFT AND SELECT LEVER SHAFT › from 2020.09
RM36W0E _52 Drivetrain _095283 EA67F MANUAL TRANSMISSION / TRANSAXLE _0449608 SHIFT AND SELECT LEVER SHAFT A

EA67F MANUAL TRANSMISSION / TRANSAXLE  SHIFT AND SELECT LEVER SHAFT  REASSEMBLY  


PROCEDURE

Hide 33528C 1.INSTALL CONTROL SHAFT COVER OIL SEAL

a.
C112481N01
0.238,0.678 0.533,0.88 0.295,0.202 10 SST 0.633,0.769 0.782,0.769 0.782,0.769 0.984,0.971 false

Using SST and a hammer, install a control shaft cover oil seal to the control shaft cover.

SST
09307-12010  

Drive in Depth:

0 to 0.5 mm (0 to 0.0197 in.)



b.

Coat a new control shaft cover oil seal lip with MP grease.


Hide 33544C 2.INSTALL SHIFT LEVER DAMPER

a.
C202999

Coat the 2 bolts with sealant.

Sealant:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



b.

Install the shift lever damper to the shift and select lever shaft with the 2 bolts.

Torque:
18.6 N*m (190 kgf*cm, 14 ft.*lbf)


Hide 33111J 3.INSTALL PIN

a.
C118049

Install the 2 pins to the No. 1 shift lever inner.


Hide 33266C 4.INSTALL SHIFT GATE PLATE

a.
C276401

Install the shift gate plate to the No. 1 shift lever inner with the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 33261C 5.INSTALL SHIFT AND SELECT LEVER SHAFT

a.

Coat the shift and select lever boot lip and shift and select lever shaft with MP grease.


b.
C276398C01
0.542,1.313 0.417,0.781 0.417,0.781 0.313,0.781 false 1.656,1.042 1.531,0.51 1.531,0.51 1.427,0.51 false 1.01,1.26 0.885,0.729 0.885,0.729 0.781,0.729 false 0.146,0.719 0.458,0.875 0.313,0.156 10 *1 0.625,0.656 0.938,0.813 0.313,0.156 10 *2 1.271,0.448 1.583,0.604 0.313,0.156 10 *3
*1 Control Shaft Cover
*2 Shift and Select Lever Boot
*3 Shift and Select Lever Shaft


Install the shift and select lever boot and control shaft cover to the shift and select lever shaft.


Hide 33251A 6.INSTALL NO. 1 SHIFT LEVER INNER

a.

Coat the shift interlock plate with MP grease.


b.
C276399C01
0.427,1.417 0.542,1.417 0.542,1.417 0.698,1.198 false 1.177,0.292 1.594,0.292 false 2.156,1.833 2.042,1.833 2.042,1.833 1.917,1.552 false 1.635,0.219 1.948,0.375 0.313,0.156 10 *1 0.24,1.354 0.552,1.51 0.313,0.156 10 *2 2.198,1.76 2.51,1.917 0.313,0.156 10 *3
*1 Shift Interlock Plate
*2 No. 1 Shift Lever Inner
*3 Shift and Select Lever Shaft


Install the No. 1 shift lever inner and shift interlock plate to the shift and select lever shaft.


c.
C203005

Using a pin punch and hammer, drive a new slotted spring pin to the No. 1 shift lever inner.

Drive in Depth:

0.4 to 1.4 mm (0.0157 to 0.0551 in.)



Hide 7.INSTALL SHIFT AND SELECT LEVER ASSEMBLY

a.
C275885

Align the 4 shift fork shafts as shown in the illustration.


b.

Clean the seal packing attached on the manual transmission case and control shaft cover using a scraper and wire brush. Then remove the oil with non-residue solvent.

NOTICE:

Do not scratch the fitting surface.



c.
C113550C07
2.938,1.219 2.594,1.073 false 3,1.156 3.385,1.5 0.385,0.344 10 *a
*a FIPG


Apply FIPG to the manual transmission case as shown in the illustration.

FIPG:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Install the parts within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.



d.
A057108C83
2.156,0.26 2.031,0.26 2.031,0.26 1.75,1.292 false 2.198,0.156 2.448,0.375 0.25,0.219 10 false *a
*a Adhesive 1344


Coat the 4 bolts with sealant.

Sealant:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



e.
C450912

Install the shift and select lever assembly to the manual transmission case with the 4 bolts.

Torque:
18.6 N*m (190 kgf*cm, 14 ft.*lbf)


Hide 84210 12.INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

Hide 13.INSTALL NO. 1 SELECTING BELL CRANK DUST COVER

a.
C116207

Install the No. 1 selecting bell crank dust cover to the selecting bell crank assembly.


Hide 14.INSTALL CONTROL SHIFT LEVER BUSHING

a.
C113636

Install the control shift lever bushing to the selecting bell crank assembly.


Hide 15.INSTALL SELECTING BELL CRANK ASSEMBLY

a.
A057108C82
2.156,0.26 2.031,0.26 2.031,0.26 1.75,1.292 false 2.198,0.156 2.448,0.375 0.25,0.219 10 false *a
*a Adhesive 1344


Coat the 2 bolts with sealant.

Sealant:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



b.
C450905

Install the selecting bell crank assembly to the manual transmission case with the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)