Home › Drivetrain › EA67F (MANUAL TRANSMISSION / TRANSAXLE) › DIFFERENTIAL CASE › from 2020.09
RM36W0E _52 Drivetrain _095283 EA67F MANUAL TRANSMISSION / TRANSAXLE _0449609 DIFFERENTIAL CASE A

EA67F MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  DISASSEMBLY  


PROCEDURE

Hide 41221 1.REMOVE FRONT DIFFERENTIAL RING GEAR

a.

Mount the front differential ring gear in a vise between aluminum plates.

NOTICE:
·

Be careful not to damage the front differential ring gear.

·

Do not overtighten the vise.




b.
C459787C01
1.948,0.594 2.49,0.917 2.49,0.917 1.813,0.677 true 2.542,0.844 2.854,1.042 0.313,0.198 10 false *a
*a Matchmark


Put matchmarks on the front differential ring gear and front No. 1 differential case sub-assembly.


c.
C117490

Remove the 16 bolts.


d.

Using a plastic-faced hammer, remove the front No. 1 differential case sub-assembly from the front differential ring gear.


Hide 41301L 2.INSPECT FRONT NO. 1 DIFFERENTIAL CASE SUB-ASSEMBLY (w/o LSD)

Hide 41342A 3.REMOVE FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN (w/o LSD)

a.
C459788

Using a 5 mm pin punch and hammer, remove the front differential pinion shaft straight pin from the front No. 1 differential case sub-assembly.


Hide 41342F 4.REMOVE FRONT NO. 1 DIFFERENTIAL PINION SHAFT (w/o LSD)

a.
C460119

Remove the front No. 1 differential pinion shaft from the front No. 1 differential case sub-assembly.


Hide 5.INSPECT FRONT DIFFERENTIAL PINION BACKLASH (w/o LSD)

Hide 41331F 6.REMOVE FRONT DIFFERENTIAL SIDE GEAR (w/o LSD)

a.

Set SST as shown in the illustration and tighten it.

C460120C01
4.542,0.552 5.052,0.552 false 4.917,1.531 4.323,1.427 4.323,1.427 4.906,1.313 true 0.958,2.344 1.271,2.542 0.313,0.198 10 false *b 2.76,0.396 3.073,0.594 0.313,0.198 10 false *a 4.25,0.458 4.635,0.646 0.385,0.188 10 false SST 4.031,1.344 4.417,1.531 0.385,0.188 10 false SST
*a Turn *b Hold


SST
09528-52010  (09528-05010, 09953-05010)

NOTICE:

Do not overtighten SST, as doing so will damage the front differential side gear, conical spring, front No. 1 differential side gear thrust washer and front No. 1 differential case sub-assembly.


HINT:
·

Tighten SST until there is a clearance between the front differential pinions and front differential side gears.

·

When removing the front differential pinions, do not overtighten SST, as it is necessary to rotate the front differential side gears.




b.
C460121C01
1.865,1.323 2.063,1.323 2.063,1.323 2.479,1.927 true 1.458,0.667 1.771,0.865 0.313,0.198 10 false *a 1.573,1.26 1.938,1.448 0.365,0.188 10 false SST
*a Turn


Install SST as shown in the illustration, rotate the front differential side gear, and then remove the 2 front differential pinions and 2 front differential pinion thrust washers from the front No. 1 differential case sub-assembly.

SST
09528-52010  (09528-05030)

NOTICE:

Do not drop the front differential pinion and front differential pinion thrust washer.



c.
C460122C01
1.771,0.469 2,0.469 2,0.469 2.427,0.781 true 2.385,1.51 2.167,1.635 2.167,1.635 2.396,1.781 true 1.802,2.865 2.031,2.865 2.031,2.865 2.396,2.51 true 1.771,2.51 2,2.51 2,2.51 2.26,2.354 true 1.76,0.813 1.99,0.813 1.99,0.813 2.271,0.927 true 2,1.552 2.313,1.75 0.313,0.198 10 false *1 1.604,0.729 1.813,0.917 0.208,0.188 10 false *2 1.615,0.385 1.823,0.573 0.208,0.188 10 false *3 1.635,2.427 1.813,2.635 0.177,0.208 10 false *2 1.625,2.781 1.833,2.969 0.208,0.188 10 false *3
*1 Front Differential Side Gear
*2 Conical Spring
*3 Front No. 1 Differential Side Gear Thrust Washer


Remove SST from the front No. 1 differential case sub-assembly, and then remove the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical springs from the front No. 1 differential case sub-assembly.

NOTICE:

Do not drop the front differential side gear, front No. 1 differential side gear thrust washer and conical spring.