Home › Drivetrain › EA67F (MANUAL TRANSMISSION / TRANSAXLE) › DIFFERENTIAL CASE › from 2020.09
RM36W0E _52 Drivetrain _095283 EA67F MANUAL TRANSMISSION / TRANSAXLE _0449609 DIFFERENTIAL CASE A

EA67F MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 41331F 1.INSTALL FRONT DIFFERENTIAL SIDE GEAR (w/o LSD)

a.
C288461C01
0.771,0.688 0.635,0.302 0.635,0.302 0.552,0.302 false 1.719,0.719 1.583,0.333 1.583,0.333 1.5,0.333 false 2.5,0.708 2.365,0.323 2.365,0.323 2.281,0.323 false 0.406,0.229 0.719,0.385 0.313,0.156 10 false *1 1.323,0.25 1.635,0.406 0.313,0.156 10 false *2 2.104,0.25 2.417,0.406 0.313,0.156 10 false *3
*1 Front Differential Side Gear
*2 Conical Spring
*3 Front No. 1 Differential Side Gear Thrust Washer
V100135

Gear Oil


Coat the front differential side gear, front No. 1 differential side gear thrust washer and conical spring with gear oil.


b.
C460122C01
1.771,0.469 2,0.469 2,0.469 2.427,0.781 true 2.385,1.51 2.167,1.635 2.167,1.635 2.396,1.781 true 1.802,2.865 2.031,2.865 2.031,2.865 2.396,2.51 true 1.771,2.51 2,2.51 2,2.51 2.26,2.354 true 1.76,0.813 1.99,0.813 1.99,0.813 2.271,0.927 true 2,1.552 2.313,1.75 0.313,0.198 10 false *1 1.604,0.729 1.813,0.917 0.208,0.188 10 false *2 1.615,0.385 1.823,0.573 0.208,0.188 10 false *3 1.635,2.427 1.813,2.635 0.177,0.208 10 false *2 1.625,2.781 1.833,2.969 0.208,0.188 10 false *3
*1 Front Differential Side Gear
*2 Conical Spring
*3 Front No. 1 Differential Side Gear Thrust Washer


Install the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical springs to the front No. 1 differential case sub-assembly.

NOTICE:
·

Do not drop the front differential side gear, front No. 1 differential side gear thrust washer and conical spring.

·

Make sure that the conical spring is installed in the correct orientation.




c.

Set SST as shown in the illustration and tighten it.

C460120C01
4.542,0.552 5.052,0.552 false 4.917,1.531 4.323,1.427 4.323,1.427 4.906,1.313 true 0.958,2.344 1.271,2.542 0.313,0.198 10 false *b 2.76,0.396 3.073,0.594 0.313,0.198 10 false *a 4.25,0.458 4.635,0.646 0.385,0.188 10 false SST 4.031,1.344 4.417,1.531 0.385,0.188 10 false SST
*a Turn *b Hold


SST
09528-52010  (09528-05010, 09953-05010)

NOTICE:

Do not overtighten SST, as doing so will damage the front differential side gear, conical spring, front No. 1 differential side gear thrust washer and front No. 1 differential case sub-assembly.


HINT:
·

Tighten SST to create the necessary clearance to install the front differential pinions.

·

When installing the front differential pinions, do not overtighten SST, as it is necessary to rotate the front differential side gears.




d.
C301356C01
0,0 0,0 false
V100135

Gear Oil


Coat the front differential pinion and front differential pinion thrust washer with gear oil.


e.
C460123C01
1.865,1.323 2.063,1.323 2.063,1.323 2.479,1.927 true 1.344,1.01 1.656,1.208 0.313,0.198 10 false *a 1.573,1.26 1.938,1.448 0.365,0.188 10 false SST
*a Turn


Using SST as shown in the illustration, rotate the front differential side gear and install the 2 front differential pinions and 2 front differential pinion thrust washers.

SST
09528-52010  (09528-05030)

CAUTION:

Be careful not to catch your fingers between the front differential pinion and front No. 1 differential case sub-assembly.


NOTICE:

Do not drop the front differential pinion and front differential pinion thrust washer.



Hide 2.INSPECT FRONT DIFFERENTIAL PINION BACKLASH (w/o LSD)

Hide 41342F 3.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT (w/o LSD)

a.
C460124C01
0,0 0,0 false
V100135

Gear Oil


Coat a front No. 1 differential pinion shaft with gear oil.


b.

Install the front No. 1 differential pinion shaft to the front No. 1 differential case sub-assembly so that the hole for the front differential pinion shaft straight pin is aligned with the hole in the front No. 1 differential case sub-assembly.


Hide 41301L 4.INSPECT FRONT NO. 1 DIFFERENTIAL CASE SUB-ASSEMBLY (w/o LSD)

Hide 41342A 5.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN (w/o LSD)

a.
C460125

Using a 5 mm pin punch and hammer, install the front differential pinion shaft straight pin to the front No. 1 differential case sub-assembly.


b.
C460126

Using a chisel and hammer, stake the front No. 1 differential case sub-assembly.


Hide 41221 6.INSTALL FRONT DIFFERENTIAL RING GEAR

a.

Using a heater, heat the front differential ring gear to 90 to 100°C (194 to 212°F).

CAUTION:
C326860

Use thick gloves to protect your hands as the front differential ring gear is hot.



b.

Clean the contact surface of the front No. 1 differential case sub-assembly and front differential ring gear.


c.
C459787C01
1.948,0.594 2.49,0.917 2.49,0.917 1.813,0.677 true 2.542,0.844 2.854,1.042 0.313,0.198 10 false *a
*a Matchmark


While aligning the matchmarks, quickly install the front differential ring gear to the front No. 1 differential case sub-assembly with the 16 bolts.

Torque:
106 N*m (1081 kgf*cm, 78 ft.*lbf)