Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION
When replacing the telephone transceiver assembly, make sure to replace it with a new one.
Inspect the fuses and relays related to this system before inspecting the suspected areas below.
Check the vehicle specification.
| Result | Proceed to |
|---|---|
| for TMMF Made | A |
| for TMC Made | B |
A
B
Disconnect the H85 telephone transceiver assembly connector.
Disconnect the V6 map light assembly (manual (SOS) switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H85-3 (SIG-) - V6-16 (GND3) | Always | Below 1 Ω |
| H85-3 (SIG-) or V6-16 (GND3) - Body ground | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| V6-9 (RRID) - Body Ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Map Light Assembly (Manual (SOS) Switch)) |
Remove the map light assembly (manual (SOS) switch).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Apply auxiliary battery voltage to the connector.
| Measurement Condition | Condition | Specified Condition |
|---|---|---|
| Auxiliary battery positive (+) → V6-9 (RRID)
Auxiliary battery negative (-) → V6-16 (GND3) |
Always | Manual (SOS) switch illumination comes on |
Check if the manual (SOS) switch illumination comes on.
The manual (SOS) switch illumination comes on.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the H85 telephone transceiver assembly connector.
Disconnect the V7 map light assembly (manual (SOS) switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H85-3 (SIG-) - V7-5 (GND3) | Always | Below 1 Ω |
| H85-3 (SIG-) or V7-5 (GND3) - Body ground | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| V7-8 (RRID) - Body Ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Map Light Assembly (Manual (SOS) Switch)) |
Remove the map light assembly (manual (SOS) switch).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Apply auxiliary battery voltage to the connector.
| Measurement Condition | Condition | Specified Condition |
|---|---|---|
| Auxiliary battery positive (+) → V7-8 (RRID)
Auxiliary battery negative (-) → V7-5 (GND3) |
Always | Manual (SOS) switch illumination comes on |
Check if the manual (SOS) switch illumination comes on.
The manual (SOS) switch illumination comes on.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT