Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.09
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0420309 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B00751A  Second Row Right Seat Belt Pretensioner Deployment Control Circuit Resistance Below Threshold  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B00751A Second Row Right Seat Belt Pretensioner Deployment Control Circuit Resistance Below Threshold
·

The airbag sensor assembly detects a line short in the right side 2nd seat pretensioner squib circuit for 2 seconds during the primary check

·

Rear seat outer belt assembly RH malfunction

·

Airbag sensor assembly malfunction


·

Harness or connector

·

Rear seat outer belt assembly RH

·

Airbag sensor assembly


Comes on Applies to check mode

WIRING DIAGRAM

B502460E68
4.896,3.083 6.938,3.635 2.042,0.552 10 false Airbag Sensor Assembly 4.885,2.917 6.448,3.094 1.563,0.177 10 false O24 4.688,1.333 4.917,1.667 0.229,0.333 10 false 12 4.688,1.896 4.917,2.167 0.229,0.271 10 false 11 4.958,1.333 5.76,1.979 0.802,0.646 10 false PRR+ 4.958,1.896 5.76,2.542 0.802,0.646 10 false PRR- 0.875,2.406 2.479,2.594 1.604,0.188 10 false O16 0.875,2.573 3.385,3.417 2.51,0.844 10 false Rear Seat Outer Belt Assembly RH 2.083,1.333 2.885,1.979 0.802,0.646 10 false 1 2.083,1.885 2.885,2.531 0.802,0.646 10 false 2 1.708,1.333 2.51,1.979 0.802,0.646 10 false RR+ 1.74,1.885 2.542,2.531 0.802,0.646 10 false RR-

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:
·

To perform the simulation method, select Check Mode with the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

Perform the simulation method while checking the Data List.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST



PROCEDURE

1.CHECK CURRENT DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
Current B00751A is output A
History B00751A is output B



Post-procedure1

c.

None



A

2.CHECK CONNECTION OF CONNECTORS

B

USE SIMULATION METHOD TO CHECK

2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Procedure1

c.

Check that the connectors are properly connected to the rear seat outer belt assembly RH and airbag sensor assembly.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS

Pre-procedure1

a.

Disconnect the connectors from the rear seat outer belt assembly RH and airbag sensor assembly.


Procedure1

b.
C422858C02
0.521,1.021 0.521,1.635 false 1.365,0.521 1.365,0.885 false 2.469,1.188 2.771,1.625 0.302,0.438 10 false *2 0.448,1.656 0.896,1.99 0.448,0.333 10 false *1 1.281,0.323 1.583,0.51 0.302,0.188 10 false *3
*1 Rear Seat Outer Belt Assembly RH
*2 Airbag Sensor Assembly
*3 Wire Harness


Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.



c.

Check that the short springs of the activation prevention mechanism of the wire harness connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



d.

Check that the wire harness connector (on the rear seat outer belt assembly RH side) is not loose, deformed or damaged.

OK:

The airbag connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

e.

None



OK

4.CHECK REAR SEAT OUTER BELT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK REAR SEAT OUTER BELT ASSEMBLY RH
a.
C422851C08
0.396,2.25 0.771,2.521 0.375,0.271 0.667,0.667 0.667,1.063 false 1.802,2.313 1.979,2.313 false 1.49,0.656 1.49,1.052 false 0.594,1.073 0.99,1.417 0.396,0.344 10 false *1 2.26,0.823 2.573,1.156 0.313,0.333 10 false *2 1.802,0.51 1.99,0.75 0.188,0.24 10 false A 1.646,0.51 2.229,0.948 0.583,0.438 10 false B 1.146,0.51 1.344,0.771 0.198,0.26 10 false C 0.781,0.51 1.365,1.052 0.583,0.542 10 false D 0.438,2.281 0.781,2.5 0.344,0.219 10 false O16 2.01,2.219 2.448,2.563 0.438,0.344 10 false SST 0.344,1.719 0.646,2 0.302,0.281 10 false *a 1.417,1.073 1.698,1.292 0.281,0.219 10 false *3
*1 Rear Seat Outer Belt Assembly RH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Rear Seat Outer Belt Assembly RH)


Connect the connector to the airbag sensor assembly.


b.

Connect the white wire side of SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the rear seat outer belt assembly RH for measurement, as this may lead to a serious injury due to pretensioner deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

f.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

5.CHECK REAR SEAT OUTER BELT ASSEMBLY RH
5.CHECK REAR SEAT OUTER BELT ASSEMBLY RH

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTC B00751A may be output at this time, but they are not related to this check.



Result:
Result Proceed to
B00751A is not output A
B00751A is output B


Post-procedure1

c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



e.

Disconnect SST from connector C.



A

REPLACE REAR SEAT OUTER BELT ASSEMBLY RH

B

6.CHECK WIRE HARNESS (SHORT)
6.CHECK WIRE HARNESS (SHORT)

Pre-procedure1

a.

Disconnect the connector from the airbag sensor assembly.


b.

Release the activation prevention mechanism built into connector B.

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>SYSTEM DESCRIPTION



Procedure1

c.
C422852C08
0.604,2.375 0.969,2.604 0.365,0.229 1.531,2.333 1.844,2 true 1.031,2 1.333,2.333 true 0.583,1 0.583,0.667 false 1.417,1 1.417,0.667 false 0.5,1.021 0.75,1.333 0.25,0.313 10 false *1 2.396,0.833 2.771,1.271 0.375,0.438 10 false *2 1.938,0.51 2.24,0.865 0.302,0.354 10 false A 1.563,0.51 1.906,1.052 0.344,0.542 10 false B 1.052,0.51 1.49,0.906 0.438,0.396 10 false C 0.677,0.51 1.115,0.896 0.438,0.385 10 false D 1.885,1.917 2.281,2.26 0.396,0.344 10 false RR- 0.698,1.917 1.156,2.156 0.458,0.24 10 false RR+ 0.354,1.844 0.75,2.135 0.396,0.292 10 false *a 0.646,2.385 1.01,2.698 0.365,0.313 10 false O16 1.365,1.021 1.667,1.333 0.302,0.313 10 false *3
*1 Rear Seat Outer Belt Assembly RH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Rear Seat Outer Belt Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O16-1 (RR+) - O16-2 (RR-) Always 1 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

Restore the released activation prevention mechanism of connector B to the original condition.



OK

7.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CLEAR DTC
a.
C422848C02
0.813,0.833 0.813,1.156 false 0.927,0.688 1.083,1 0.156,0.313 10 false D 1.083,0.688 1.229,0.948 0.146,0.26 10 false C 1.583,0.688 1.74,0.948 0.156,0.26 10 false B 1.74,0.688 1.979,1 0.24,0.313 10 false A 2.188,1 2.625,1.344 0.438,0.344 10 false *2 0.74,1.177 0.99,1.417 0.25,0.24 10 false *1
*1 Rear Seat Outer Belt Assembly RH
*2 Airbag Sensor Assembly


Connect the connectors to the rear seat outer belt assembly RH and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

e.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

8.CHECK DTC
8.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTC B00751A may be output at this time, but they are not related to this check.


Result:
Result Proceed to
B00751A is not output A
B00751A is output B



Post-procedure1

c.

None



A

USE SIMULATION METHOD TO CHECK

B