This DTC is stored when a malfunction occurs in the speakers.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C3 | Speaker Output Short | A short is detected in the speaker output circuit | ·
Harness or connector ·
Speaker ·
Radio and Display Receiver Assembly |
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for 2 Speakers | A |
| for 4 Speakers | B |
| for 6 Speakers | C |
| for 8 Speakers | D |
A
B
C
D
Disconnect the H83 radio and display receiver assembly connector.
Disconnect the H129 and H130 wiring harness connector connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H83-1 (FR+) or H130-3 (+) - Body ground | Always | 10 kΩ or higher |
| H83-6 (FR-) or H130-1 (-) - Body ground | Always | 10 kΩ or higher |
| H83-2 (FL+) or H129-3 (+) - Body ground | Always | 10 kΩ or higher |
| H83-7 (FL-) or H129-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K2 and L2 front No. 1 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H130-4 (TWR+) or K2-2 - Body ground | Always | 10 kΩ or higher |
| H130-2 (TWR-) or K2-1 - Body ground | Always | 10 kΩ or higher |
| H129-4 (TWL+) or L2-2 - Body ground | Always | 10 kΩ or higher |
| H129-2 (TWL-) or L2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/o Active Noise Control System | A |
| w/ Active Noise Control System | B |
A
B
Disconnect the H83 radio and display receiver assembly connector.
Disconnect the H129 and H130 wiring harness connector connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H83-1 (FR+) or H130-3 (+) - Body ground | Always | 10 kΩ or higher |
| H83-6 (FR-) or H130-1 (-) - Body ground | Always | 10 kΩ or higher |
| H83-2 (FL+) or H129-3 (+) - Body ground | Always | 10 kΩ or higher |
| H83-7 (FL-) or H129-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K2 and L2 front No. 1 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H130-4 (TWR+) or K2-2 - Body ground | Always | 10 kΩ or higher |
| H130-2 (TWR-) or K2-1 - Body ground | Always | 10 kΩ or higher |
| H129-4 (TWL+) or L2-2 - Body ground | Always | 10 kΩ or higher |
| H129-2 (TWL-) or L2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H83 radio and display receiver assembly connector.
Disconnect the M2 and N2 rear speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H83-4 (RR+) or M2-2 - Body ground | Always | 10 kΩ or higher |
| H83-9 (RR-) or M2-1 - Body ground | Always | 10 kΩ or higher |
| H83-3 (RL+) or N2-2 - Body ground | Always | 10 kΩ or higher |
| H83-8 (RL-) or N2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the rear speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
A
B
Disconnect the O131 stereo component equalizer assembly connector.
Disconnect the K2 and L2 front no. 1 speaker assembly connector connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O131-12 (FR+) or K2-2 - Body ground | Always | 10 kΩ or higher |
| O131-27 (FR-) or K2-1 - Body ground | Always | 10 kΩ or higher |
| O131-13 (FL+) or L2-2 - Body ground | Always | 10 kΩ or higher |
| O131-28 (FL-) or L2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O131 stereo component equalizer assembly connector.
Disconnect the O114 and O115 rear speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O131-10 (RR+) or O114-2 - Body ground | Always | 10 kΩ or higher |
| O131-25 (RR-) or O114-1 - Body ground | Always | 10 kΩ or higher |
| O131-11 (RL+) or O115-2 - Body ground | Always | 10 kΩ or higher |
| O131-26 (RL-) or O115-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the rear speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
A
B
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/o Active Noise Control System | A |
| w/ Active Noise Control System | B |
A
B
Disconnect the H83 radio and display receiver assembly connector.
Disconnect the H88 and H87 front No. 2 speaker assembly connectors.
Disconnect the M2 and N2 rear speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H83-1 (FR+) or H88-3 (+) - Body ground | Always | 10 kΩ or higher |
| H83-6 (FR-) or H88-1 (-) - Body ground | Always | 10 kΩ or higher |
| H83-2 (FL+) or H87-3 (+) - Body ground | Always | 10 kΩ or higher |
| H83-7 (FL-) or H87-1 (-) - Body ground | Always | 10 kΩ or higher |
| H83-4 (RR+) or M2-2 - Body ground | Always | 10 kΩ or higher |
| H83-9 (RR-) or M2-1 - Body ground | Always | 10 kΩ or higher |
| H83-3 (RL+) or N2-2 - Body ground | Always | 10 kΩ or higher |
| H83-8 (RL-) or N2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K2 and L2 front No. 1 speaker assembly connectors.
Disconnect the H88 and H87 front No. 2 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H88-4 (TWR+) or K2-2 - Body ground | Always | 10 kΩ or higher |
| H88-2 (TWR-) or K2-1 - Body ground | Always | 10 kΩ or higher |
| H87-4 (TWL+) or L2-2 - Body ground | Always | 10 kΩ or higher |
| H87-2 (TWL-) or L2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 2 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
A
B
Disconnect the O131 stereo component equalizer assembly connector.
Disconnect the H88 and H87 front No. 2 speaker assembly connectors.
Disconnect the O115 and O114 rear speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O131-12 (FR+) or H88-3 (+) - Body ground | Always | 10 kΩ or higher |
| O131-27 (FR-) or H88-1 (-) - Body ground | Always | 10 kΩ or higher |
| O131-13 (FL+) or H87-3 (+) - Body ground | Always | 10 kΩ or higher |
| O131-28 (FL-) or H87-1 (-) - Body ground | Always | 10 kΩ or higher |
| O131-10 (RR+) or O115-2 - Body ground | Always | 10 kΩ or higher |
| O131-25 (RR-) or O115-1 - Body ground | Always | 10 kΩ or higher |
| HO131-26 (RL+) or O114-2 - Body ground | Always | 10 kΩ or higher |
| O131-26 (RL-) or O114-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K2 and L2 front No. 1 speaker assembly connectors.
Disconnect the H88 and H87 front No. 2 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H88-4 (TWR+) or K2-2 - Body ground | Always | 10 kΩ or higher |
| H88-2 (TWR-) or K2-1 - Body ground | Always | 10 kΩ or higher |
| H87-4 (TWL+) or L2-2 - Body ground | Always | 10 kΩ or higher |
| H87-2 (TWL-) or L2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 2 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
A
B
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| except G16E-GTS | A |
| for G16E-GTS | B |
A
B
Disconnect the H136 stereo component amplifier assembly connector.
Disconnect the K2 and L2 front No. 1 speaker assembly connectors.
Disconnect the H88 and H87 front No. 2 speaker assembly connectors.
Disconnect the H139 and H138 front No. 4 speaker assembly connectors.
Disconnect the M2 and N2 rear speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H136-10 (WFR+) or K2-2 - Body ground | Always | 10 kΩ or higher |
| H136-25 (WFR-) or K2-1 - Body ground | Always | 10 kΩ or higher |
| H136-8 (WFL+) or L2-2 - Body ground | Always | 10 kΩ or higher |
| H136-23 (WFL-) or L2-1 - Body ground | Always | 10 kΩ or higher |
| H136-14 (TWR+) or H88-4 - Body ground | Always | 10 kΩ or higher |
| H136-29 (TWR-) or H88-2 - Body ground | Always | 10 kΩ or higher |
| H136-12 (TWL+) or H87-4 - Body ground | Always | 10 kΩ or higher |
| H136-27 (TWL-) or H87-2 - Body ground | Always | 10 kΩ or higher |
| H136-11 (FR+) or H139-2 - Body ground | Always | 10 kΩ or higher |
| H136-26 (FR-) or H139-1 - Body ground | Always | 10 kΩ or higher |
| H136-9 (FL+) or H138-2 - Body ground | Always | 10 kΩ or higher |
| H136-24 (FL-) or H138-1 - Body ground | Always | 10 kΩ or higher |
| H136-15 (RR+) or M2-2 - Body ground | Always | 10 kΩ or higher |
| H136-30 (RR-) or M2-1 - Body ground | Always | 10 kΩ or higher |
| H136-13 (RL+) or N2-2 - Body ground | Always | 10 kΩ or higher |
| H136-28 (RL-) or N2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 2 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
A
B
Disconnect the O121 stereo component amplifier assembly connector.
Disconnect the K2 and L2 front No. 1 speaker assembly connectors.
Disconnect the H88 and H87 front No. 2 speaker assembly connectors.
Disconnect the H139 and H138 front No. 4 speaker assembly connectors.
Disconnect the O115 and O114 rear speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O121-10 (WFR+) or K2-2 - Body ground | Always | 10 kΩ or higher |
| O121-25 (WFR-) or K2-1 - Body ground | Always | 10 kΩ or higher |
| O121-8 (WFL+) or L2-2 - Body ground | Always | 10 kΩ or higher |
| O121-23 (WFL-) or L2-1 - Body ground | Always | 10 kΩ or higher |
| O121-14 (TWR+) or H88-4 - Body ground | Always | 10 kΩ or higher |
| O121-29 (TWR-) or H88-2 - Body ground | Always | 10 kΩ or higher |
| O121-12 (TWL+) or H87-4 - Body ground | Always | 10 kΩ or higher |
| O121-27 (TWL-) or H87-2 - Body ground | Always | 10 kΩ or higher |
| O121-11 (FR+) or H139-2 - Body ground | Always | 10 kΩ or higher |
| O121-26 (FR-) or H139-1 - Body ground | Always | 10 kΩ or higher |
| O121-9 (FL+) or H138-2 - Body ground | Always | 10 kΩ or higher |
| O121-24 (FL-) or H138-1 - Body ground | Always | 10 kΩ or higher |
| O121-15 (RR+) or O115-2 - Body ground | Always | 10 kΩ or higher |
| O121-30 (RR-) or O115-1 - Body ground | Always | 10 kΩ or higher |
| O121-13 (RL+) or O114-2 - Body ground | Always | 10 kΩ or higher |
| O121-28 (RL-) or O114-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 2 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
A
B