Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.09
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0420309 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B002011  Left Side Airbag Deployment Control Circuit Short to Ground  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B002011 Left Side Airbag Deployment Control Circuit Short to Ground
·

The airbag sensor assembly detects a short to ground in the left side 1st seat side-airbag squib circuit for 0.5 seconds

·

Front seat airbag assembly LH malfunction

·

Airbag sensor assembly malfunction


·

Harness or connector

·

Front seat airbag assembly LH

·

Airbag sensor assembly


Comes on Applies to check mode

WIRING DIAGRAM

B502460E61
4.896,3.083 6.75,3.49 1.854,0.406 10 false Airbag Sensor Assembly 4.885,2.917 5.802,3.125 0.917,0.208 10 false O24 4.708,1.333 5.51,1.979 0.802,0.646 10 false 16 4.719,1.896 5.521,2.542 0.802,0.646 10 false 15 1.625,1.333 2.083,1.5 0.458,0.167 10 false SFL+ 4.958,1.896 5.417,2.083 0.458,0.188 10 false SFL- 0.5,2.396 1,2.583 0.5,0.188 10 false O100 0.5,2.573 4.333,3.083 3.833,0.51 10 false Front Seat Airbag Assembly LH 2.094,1.875 2.896,2.521 0.802,0.646 10 false 2 2.094,1.323 2.896,1.969 0.802,0.646 10 false 1 4.958,1.333 5.417,1.5 0.458,0.167 10 false SFL+ 1.625,1.896 2,2.083 0.375,0.188 10 false SFL-

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:
·

To perform the simulation method, select Check Mode with the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

Perform the simulation method while checking the Data List.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST



PROCEDURE

1.CHECK CURRENT DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
Current B002011 is output A
History B002011 is output B



Post-procedure1

c.

None



A

2.CHECK CONNECTION OF CONNECTORS

B

USE SIMULATION METHOD TO CHECK

2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Procedure1

c.

Check that the connectors are properly connected to the front seat airbag assembly LH and airbag sensor assembly.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS

Pre-procedure1

a.
C422858C02
0.521,1.021 0.521,1.635 false 1.365,0.521 1.365,0.885 false 2.469,1.188 2.771,1.625 0.302,0.438 10 false *2 0.448,1.656 0.896,1.99 0.448,0.333 10 false *1 1.281,0.323 1.583,0.51 0.302,0.188 10 false *3
*1 Front Seat Airbag Assembly LH
*2 Airbag Sensor Assembly
*3 Wire Harness


Disconnect the connectors from the front seat airbag assembly LH and airbag sensor assembly.


Procedure1

b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.



c.

Check that the short springs of the activation prevention mechanism of the wire harness connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.CHECK FRONT SEAT AIRBAG ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FRONT SEAT AIRBAG ASSEMBLY LH
a.
C422846C03
0.375,2.146 0.813,2.406 0.438,0.26 0.594,0.885 0.594,0.552 false 2.271,2.417 2.5,2.417 false 1.521,0.885 1.521,0.552 false 0.521,0.906 0.844,1.177 0.323,0.271 10 false *1 2.479,0.74 2.854,1.063 0.375,0.323 10 false *2 0.333,1.615 0.667,2.031 0.333,0.417 10 false *a 2.552,2.323 2.917,2.583 0.365,0.26 10 false SST 0.427,2.177 0.802,2.396 0.375,0.219 10 false O100 2.021,0.406 2.177,0.635 0.156,0.229 10 false A 1.854,0.406 2,0.656 0.146,0.25 10 false B 1.104,0.396 1.24,0.625 0.135,0.229 10 false C 0.729,0.396 0.885,0.625 0.156,0.229 10 false D 1.448,0.917 1.771,1.188 0.323,0.271 10 false *3
*1 Front Seat Airbag Assembly LH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Front Seat Airbag Assembly LH)


Connect the connector to the airbag sensor assembly.


b.

Connect the red wire side of SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the front seat airbag assembly LH for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

f.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

5.CHECK FRONT SEAT AIRBAG ASSEMBLY LH
5.CHECK FRONT SEAT AIRBAG ASSEMBLY LH

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTC B002011 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
B002011 is not output A
B002011 is output B


Post-procedure1

c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



e.

Disconnect SST from connector C.



A

B

6.CHECK WIRE HARNESS (SHORT TO GROUND)
6.CHECK WIRE HARNESS (SHORT TO GROUND)

Pre-procedure1

a.

Disconnect the connector from the airbag sensor assembly.


Procedure1

b.
C422847C03
0.375,2.25 0.792,2.49 0.417,0.24 0.563,0.719 0.563,1.167 false 1.417,0.719 1.417,1.167 false 0.833,2.833 1.375,2.5 true 2.083,2.833 1.583,2.5 true 0.667,0.563 0.885,0.792 0.219,0.229 10 false D 1.063,0.563 1.354,0.844 0.292,0.281 10 false C 1.583,0.563 1.865,0.948 0.281,0.385 10 false B 1.979,0.563 2.208,0.896 0.229,0.333 10 false A 2.406,0.875 2.75,1.25 0.344,0.375 10 false *2 0.5,1.177 0.833,1.417 0.333,0.24 10 false *1 0.313,1.74 0.604,2.031 0.292,0.292 10 false *a 0.417,2.271 0.771,2.469 0.354,0.198 10 false O100 1.354,1.177 1.656,1.417 0.302,0.24 10 false *3 0.677,2.854 1.104,3.083 0.427,0.229 10 false SFL+ 1.99,2.854 2.417,3.083 0.427,0.229 10 false SFL-
*1 Front Seat Airbag Assembly LH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Front Seat Airbag Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O100-1 (SFL+) - Body ground Always 1 MΩ or higher
O100-2 (SFL-) - Body ground Always 1 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

7.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CLEAR DTC
a.
C422848C02
0.813,0.833 0.813,1.156 false 0.927,0.688 1.083,1 0.156,0.313 10 false D 1.083,0.688 1.229,0.948 0.146,0.26 10 false C 1.583,0.688 1.74,0.948 0.156,0.26 10 false B 1.74,0.688 1.979,1 0.24,0.313 10 false A 2.188,1 2.625,1.344 0.438,0.344 10 false *2 0.74,1.177 0.99,1.417 0.25,0.24 10 false *1
*1 Front Seat Airbag Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the front seat airbag assembly LH and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

e.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

8.CHECK DTC
8.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTC B002011 may be output at this time, but they are not related to this check.


Result:
Result Proceed to
B002011 is not output A
B002011 is output B



Post-procedure1

c.

None



A

USE SIMULATION METHOD TO CHECK

B