Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.09
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0420309 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B002912  Right Curtain Deployment Control 1 Circuit Short to Battery  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B002912 Right Curtain Deployment Control 1 Circuit Short to Battery
·

The airbag sensor assembly detects a short to B+ in the right side curtain shield airbag squib circuit for 0.5 seconds

·

Curtain shield airbag assembly RH malfunction

·

Airbag sensor assembly malfunction


·

Harness or connector

·

Curtain shield airbag assembly RH

·

Airbag sensor assembly


Comes on Applies to check mode

WIRING DIAGRAM

B502460E64
4.896,3.083 7.01,3.49 2.115,0.406 10 false Airbag Sensor Assembly 4.885,2.917 6.313,3.115 1.427,0.198 10 false O24 4.781,1.333 5.583,1.979 0.802,0.646 10 false 1 4.781,1.896 5.583,2.542 0.802,0.646 10 false 2 4.958,1.333 5.76,1.979 0.802,0.646 10 false ICR+ 4.958,1.896 5.76,2.542 0.802,0.646 10 false ICR- 0.271,2.406 1.302,2.604 1.031,0.198 10 false O12 0.271,2.573 4.167,3.083 3.896,0.51 10 false Curtain Shield Airbag Assembly RH 2.083,1.333 2.885,1.979 0.802,0.646 10 false 1 2.083,1.885 2.885,2.531 0.802,0.646 10 false 2 1.677,1.333 2.479,1.979 0.802,0.646 10 false ICR+ 1.708,1.885 2.51,2.531 0.802,0.646 10 false ICR-

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:
·

To perform the simulation method, select Check Mode with the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

Perform the simulation method while checking the Data List.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST



PROCEDURE

1.CHECK CURRENT DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
Current B002912 is output A
History B002912 is output B



Post-procedure1

c.

None



A

2.CHECK CONNECTION OF CONNECTORS

B

USE SIMULATION METHOD TO CHECK

2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Procedure1

c.

Check that the connectors are properly connected to the curtain shield airbag assembly RH and airbag sensor assembly.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS

Pre-procedure1

a.

Disconnect the connectors from the curtain shield airbag assembly RH and airbag sensor assembly.


Procedure1

b.
C422858C02
0.521,1.021 0.521,1.635 false 1.365,0.521 1.365,0.885 false 2.469,1.188 2.771,1.625 0.302,0.438 10 false *2 0.448,1.656 0.896,1.99 0.448,0.333 10 false *1 1.281,0.323 1.583,0.51 0.302,0.188 10 false *3
*1 Curtain Shield Airbag Assembly RH
*2 Airbag Sensor Assembly
*3 Wire Harness


Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.



c.

Check that the short springs of the activation prevention mechanism of the wire harness connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH
a.
C422849C04
0.427,2.26 0.792,2.49 0.365,0.229 1.813,2.344 2,2.344 false 0.698,0.625 0.698,0.99 false 1.417,0.625 1.417,0.99 false 0.813,0.469 1.083,0.823 0.271,0.354 10 false D 1.125,0.469 1.323,0.708 0.198,0.24 10 false C 1.635,0.469 1.792,0.74 0.156,0.271 10 false B 1.792,0.469 2.104,0.802 0.313,0.333 10 false A 2.24,0.802 2.594,1.208 0.354,0.406 10 false *2 0.625,1.01 0.927,1.302 0.302,0.292 10 false *1 0.313,1.781 0.635,2.052 0.323,0.271 10 false *a 2.042,2.25 2.417,2.573 0.375,0.323 10 false SST 0.479,2.281 0.823,2.51 0.344,0.229 10 false O12 1.333,1.01 1.635,1.302 0.302,0.292 10 false *3
*1 Curtain Shield Airbag Assembly RH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Curtain Shield Airbag Assembly RH)


Connect the connector to the airbag sensor assembly.


b.

Connect the white wire side of SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the curtain shield airbag assembly RH for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

f.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

5.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH
5.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTC B002912 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
B002912 is not output A
B002912 is output B


Post-procedure1

c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



e.

Disconnect SST from connector C.



A

B

6.CHECK WIRE HARNESS (SHORT TO B+)
6.CHECK WIRE HARNESS (SHORT TO B+)

Pre-procedure1

a.

Disconnect the connector from the airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON.


Procedure1

d.
C422850C04
0.583,2.51 0.958,2.729 0.375,0.219 1.406,2.313 1.115,2.083 true 1.865,2.083 1.573,2.313 true 0.604,0.708 0.604,1.156 false 1.438,0.719 1.438,1.167 false 0.635,2.521 1.01,2.792 0.375,0.271 10 false O12 0.719,0.552 0.896,0.854 0.177,0.302 10 false D 1.073,0.552 1.25,0.854 0.177,0.302 10 false C 1.583,0.552 1.719,0.833 0.135,0.281 10 false B 1.938,0.563 2.115,0.802 0.177,0.24 10 false A 2.385,0.896 2.844,1.302 0.458,0.406 10 false *2 0.531,1.167 1,1.427 0.469,0.26 10 false *1 0.313,1.802 0.646,2.073 0.333,0.271 10 false *a 1.906,1.969 2.375,2.292 0.469,0.323 10 false ICR- 0.75,1.969 1.115,2.229 0.365,0.26 10 false ICR+ 1.375,1.167 1.75,1.385 0.375,0.219 10 false *3
*1 Curtain Shield Airbag Assembly RH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Curtain Shield Airbag Assembly RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O12-1 (ICR+) - Body ground Ignition switch ON Below 1 V
O12-2 (ICR-) - Body ground Ignition switch ON Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




OK

7.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CLEAR DTC
a.
C422848C02
0.813,0.833 0.813,1.156 false 0.927,0.688 1.083,1 0.156,0.313 10 false D 1.083,0.688 1.229,0.948 0.146,0.26 10 false C 1.583,0.688 1.74,0.948 0.156,0.26 10 false B 1.74,0.688 1.979,1 0.24,0.313 10 false A 2.188,1 2.625,1.344 0.438,0.344 10 false *2 0.74,1.177 0.99,1.417 0.25,0.24 10 false *1
*1 Curtain Shield Airbag Assembly RH
*2 Airbag Sensor Assembly


Connect the connectors to the curtain shield airbag assembly RH and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

e.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

8.CHECK DTC
8.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTC B002912 may be output at this time, but they are not related to this check.


Result:
Result Proceed to
B002912 is not output A
B002912 is output B



Post-procedure1

c.

None



A

USE SIMULATION METHOD TO CHECK

B