Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY (for 5 Door) › from 2020.09
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0452650 CURTAIN SHIELD AIRBAG ASSEMBLY(for 5 Door) A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY(for 5 Door)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the curtain shield airbag assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:
·

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Stop and start system *1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
·
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 62170A 4.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY

CAUTION:
B399183C01
0.667,0.5 0.823,0.698 0.156,0.198 10 false .
V100155

Deployment Side


·

When storing the curtain shield airbag assembly, keep the airbag deployment side facing upward.

·

If the airbag deploys for any reason, it may cause a serious accident.



a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.

Disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



d.

Using needle nose pliers, remove the pins from the clips as shown in the illustration.

NOTICE:

Do not damage the pins.


B583372C01
2.646,2.583 2.979,2.583 false 5.448,2.5 4.865,2.333 4.865,2.333 5.198,2.333 true 4.927,0.708 5.167,0.542 true 2.188,0.49 1.958,0.292 true 3.75,0.5 3.521,0.302 true 2.406,2.24 2.927,2.083 2.927,2.083 2.677,2.083 true 1.344,2.25 1.854,2.083 1.854,2.083 1.604,2.083 true 3.01,2.49 3.323,2.688 0.313,0.198 10 false *a 4.667,2.25 4.896,2.448 0.229,0.198 10 false *b 5.177,0.406 5.385,0.583 0.208,0.177 10 true *1 1.74,0.188 1.948,0.365 0.208,0.177 10 true *1 3.292,0.167 3.5,0.344 0.208,0.177 10 true *2 2.948,2 3.177,2.198 0.229,0.198 10 false *c 1.865,1.979 2.094,2.177 0.229,0.198 10 false *c
*1 Clip *2 Roof Side Inner Garnish Clip
*a Pin *b Screwdriver
*c Needle nose Plier - -
V113147

Remove in this Direction - -



e.

Using 2 screwdrivers, disengage the claws of clips to separate the clips and roof side inner garnish clip from the vehicle body as shown in the illustration.

HINT:

Separate the clips and curtain shield airbag assembly from the vehicle body as a unit.



f.

Remove the 4 bolts.


g.

While holding the curtain shield airbag assembly, disengage the claws and hooks to remove the curtain shield airbag assembly.

B583373


h.

Remove the clips and roof side inner garnish clip from the curtain shield airbag assembly.