| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
| B002913 | Right Curtain Deployment Control 1 Circuit Open | ·
The airbag sensor assembly detects an open in the right side curtain shield airbag squib circuit for 2 seconds ·
Curtain shield airbag assembly RH malfunction ·
Airbag sensor assembly malfunction |
·
Harness or connector ·
Curtain shield airbag assembly RH ·
Airbag sensor assembly |
Comes on | Applies to check mode |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
To perform the simulation method, select Check Mode with the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
Perform the simulation method while checking the Data List.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST
Pre-procedure1
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| Current B002913 is output | A |
| History B002913 is output | B |
Post-procedure1
None
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Perform the simulation method by selecting Check Mode using the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
Perform the simulation method while checking the Data List.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Procedure1
Check that the connectors are properly connected to the curtain shield airbag assembly RH and airbag sensor assembly.
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the connectors from the curtain shield airbag assembly RH and airbag sensor assembly.
Procedure1
| *1 | Curtain Shield Airbag Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Wire Harness |
Check that the terminals of the connectors are not deformed or damaged.
The terminals of the connectors are not deformed or damaged.
Check that the short springs of the activation prevention mechanism of the wire harness connector are not deformed or damaged.
The short springs are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
| *1 | Curtain Shield Airbag Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector
(to Curtain Shield Airbag Assembly RH) |
Connect the connector to the airbag sensor assembly.
Connect the white wire side of SST (resistance 2.1 Ω) to connector C.
Never connect a tester to the curtain shield airbag assembly RH for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting it.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
Codes other than DTC B002913 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| B002913 is not output | A |
| B002913 is output | B |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Disconnect SST from connector C.
A
for 5 Door: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CURTAIN SHIELD AIRBAG ASSEMBLY (for 5 Door)>REMOVAL
for 3 Door: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CURTAIN SHIELD AIRBAG ASSEMBLY (for 3 Door)>REMOVAL
B
Pre-procedure1
Disconnect the connector from the airbag sensor assembly.
Procedure1
| *1 | Curtain Shield Airbag Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector
(to Curtain Shield Airbag Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O12-1 (ICR+) - O12-2 (ICR-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
| *1 | Curtain Shield Airbag Assembly RH |
| *2 | Airbag Sensor Assembly |
Connect the connectors to the curtain shield airbag assembly RH and airbag sensor assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
Codes other than DTC B002913 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| B002913 is not output | A |
| B002913 is output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Perform the simulation method by selecting Check Mode using the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
Perform the simulation method while checking the Data List.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST
B