The radio and display receiver assembly, map light assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.
This DTC is stored when a microphone connection detection signal line is disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1579 | Voice Recognition Microphone Disconnected | Microphone signal is lost | ·
Map light assembly ·
Telephone microphone assembly ·
Radio and display receiver assembly ·
Telephone transceiver assembly (w/ Telephone Transceiver Assembly) ·
Harness or connector |
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for TMC Made without Telephone Transceiver Assembly | A |
| for TMC Made with Telephone Transceiver Assembly | B |
| for TMMF Made without Telephone Transceiver Assembly | C |
| for TMMF Made with Telephone Transceiver Assembly | D |
A
B
C
D
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the V7 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H80-25 (SNS2) - V7-13 (SNS2) | Always | Below 1 Ω |
| H80-22 (MIN-) - V7-14 (MCO-) | Always | Below 1 Ω |
| H80-25 (SNS2) or V7-13 (SNS2) - Body ground | Always | 10 kΩ or higher |
| H80-22 (MIN-) or V7-14 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect the MC telephone microphone assembly connector.
| *a | Component without harness connected
(Map Light Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V7-13 (SNS2) - V7-14 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the MC telephone microphone assembly connector.
| *a | Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V7-13 (SNS2) - MC-1 (SNS2) | Always | Below 1 Ω |
| V7-14 (MCO-) - MC-2 (MIC-) | Always | Below 1 Ω |
| V7-13 (SNS2) - Body ground | Always | 10 kΩ or higher |
| V7-14 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the V7 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H80-25 (SNS2) - V7-13 (SNS2) | Always | Below 1 Ω |
| H80-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H85 telephone transceiver assembly connector.
Disconnect the V7 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H85-7 (MCI-) - V7-14 (MCO-) | Always | Below 1 Ω |
| H85-7 (MCI-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Telephone Transceiver Assembly) |
Remove the telephone transceiver assembly with the connector(s) still connected.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H85-7 (MCI-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
| *a | Component without harness connected
(Map Light Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V7-13 (SNS2) - V7-14 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side)) |
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the telephone microphone assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V7-13 (SNS2) - MC-1 (SNS2) | Always | Below 1 Ω |
| V7-14 (MCO-) - MC-2 (MIC-) | Always | Below 1 Ω |
| V7-13 (SNS2) - Body ground | Always | 10 kΩ or higher |
| V7-14 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the V6 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H80-25 (SNS2) - V6-15 (SNS2) | Always | Below 1 Ω |
| H80-22 (MIN-) - V6-4 (MCO-) | Always | Below 1 Ω |
| H80-25 (SNS2) or V6-15 (SNS2) - Body ground | Always | 10 kΩ or higher |
| H80-22 (MIN-) or V6-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect the MC telephone microphone assembly connector.
| *a | Component without harness connected
(Map Light Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V6-15 (SNS2) - V6-4 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the MC telephone microphone assembly connector.
| *a | Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V6-15 (SNS2) - MC-1 (SNS2) | Always | Below 1 Ω |
| V6-4 (MCO-) - MC-2 (MIC-) | Always | Below 1 Ω |
| V6-15 (SNS2) - Body ground | Always | 10 kΩ or higher |
| V6-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the V6 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H80-25 (SNS2) - V6-15 (SNS2) | Always | Below 1 Ω |
| H80-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H85 telephone transceiver assembly connector.
Disconnect the V6 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H85-7 (MCI-) - V6-4 (MCO-) | Always | Below 1 Ω |
| H85-7 (MCI-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Telephone Transceiver Assembly) |
Remove the telephone transceiver assembly with the connector(s) still connected.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H85-7 (MCI-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
| *a | Component without harness connected
(Map Light Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V6-15 (SNS2) - V6-4 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side)) |
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the telephone microphone assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V6-15 (SNS2) - MC-1 (SNS2) | Always | Below 1 Ω |
| V6-4 (MCO-) - MC-2 (MIC-) | Always | Below 1 Ω |
| V6-15 (SNS2) - Body ground | Always | 10 kΩ or higher |
| V6-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG