The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the occupant detection sensor removal/installation are shown below.
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Wear protective gloves. Sharp areas on the parts may injure your hands.
If a front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad, separate type front seatback cover and front seatback pad with cover with the necessary parts in accordance with the extent of the collision damage.
for 5 Door:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for 5 Door)>DISASSEMBLY
for 3 Door:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for 3 Door)>DISASSEMBLY
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1.REMOVE FRONT SEAT ASSEMBLY
Use the same procedure as for the driver side.
for 5 Door:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for 5 Door)>REMOVAL
for 3 Door:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for 3 Door)>REMOVAL
71910E
2.REMOVE FRONT SEAT HEADREST ASSEMBLY (for 5 Door)
Use the same procedure as for the driver side.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for 5 Door)>DISASSEMBLY
71074S
3.DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER (for 5 Door)
Use the same procedure as for the driver side.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for 5 Door)>DISASSEMBLY
73230
4.REMOVE FRONT SEAT INNER BELT ASSEMBLY
for 5 Door:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for 5 Door)>REMOVAL
for 3 Door:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for 3 Door)>REMOVAL
72551B
5.REMOVE RECLINING HINGE COVER
Use the same procedure as for the driver side.
for 5 Door:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for 5 Door)>DISASSEMBLY
for 3 Door:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for 3 Door)>DISASSEMBLY
72526
6.REMOVE RECLINING ADJUSTER RELEASE HANDLE
Use the same procedure as for the driver side.
for 5 Door:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for 5 Door)>DISASSEMBLY
for 3 Door:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for 3 Door)>DISASSEMBLY
71812D
7.REMOVE FRONT SEAT CUSHION SHIELD
for 5 Door:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for 5 Door)>DISASSEMBLY
for 3 Door:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for 3 Door)>DISASSEMBLY
71862
8.REMOVE FRONT SEAT INNER CUSHION SHIELD
for 5 Door:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for 5 Door)>DISASSEMBLY
for 3 Door:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for 3 Door)>DISASSEMBLY
9.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Use the same procedure as for the driver side.
for 5 Door:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for 5 Door)>DISASSEMBLY
for 3 Door:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for 3 Door)>DISASSEMBLY
10.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
Use the same procedure as for the driver side.
for 5 Door:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for 5 Door)>DISASSEMBLY
for 3 Door:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for 3 Door)>DISASSEMBLY
82667D
11.REMOVE CONNECTOR HOLDER
71511S
12.REMOVE OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD)
for 5 Door Standard Seat Type:
Using a screwdriver, disengage the claws to remove the occupant detection sensor (separate type front seat cushion pad) from the separate type front seat cushion cover as shown in the illustration.
| *a | Screwdriver | - | - |
for 5 Door Sports Seat Type:
Using a screwdriver, disengage the claws to remove the occupant detection sensor (separate type front seat cushion pad) from the separate type front seat cushion cover as shown in the illustration.
| *a | Screwdriver | - | - |
for 3 Door Sporty Seat Type:
Using a screwdriver, disengage the claws to remove the occupant detection sensor (separate type front seat cushion pad) from the separate type front seat cushion cover as shown in the illustration.
| *a | Screwdriver | - | - |
for 3 Door Sports Seat Type:
Using a screwdriver, disengage the claws to remove the occupant detection sensor (separate type front seat cushion pad) from the separate type front seat cushion cover as shown in the illustration.
| *a | Screwdriver | - | - |