Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU (for LHD) › from 2020.09
RM36W0E _57 Power Source / Network _088265 POWER DISTRIBUTION _0432922 MAIN BODY ECU(for LHD) A

POWER DISTRIBUTION  MAIN BODY ECU(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the main body ECU (multiplex network body ECU) removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
for HV Model:
Replacement of the main body ECU (multiplex network body ECU)
Code registration
·

Wireless door lock control system (w/ Entry and Start System)

·

Entry and start system (for Entry function, HV model)

·

Entry and start system (for Start function, HV model)

·

Hybrid control system cannot be started


See Service Bulletin for the registration method.
ECU configuration - (Click here)
for Gasoline Model:
Replacement of the main body ECU (multiplex network body ECU)
Code registration
·

Wireless door lock control system (w/ Entry and Start System)

·

Entry and start system (for Entry function, Gasoline model)

·

Entry and start system (for Start function, Gasoline model)

·

Engine start function


See Service Bulletin for the registration method.
ECU configuration - (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system *1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 55480D 3.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Hide 55308B 4.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

a.
B579398

Remove the 2 bolts, nut and No. 3 instrument panel to cowl brace sub-assembly.


Hide 5.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU

a.
B579391

Disconnect the 5 connectors.


b.

Disengage the clamp.


c.
B579392C01
2.365,0.74 2.51,0.583 false 2.417,1.448 2.781,1.396 true 2.271,0.75 2.583,0.948 0.313,0.198 10 false *a 2.25,1.365 2.563,1.563 0.313,0.198 10 false *a
*a Lock Lever


Disengage the claws and pull up the lock levers to disconnect the 2 connectors as shown in the illustration.


d.

Disengage the clamp.


e.

for HV Model:

i.
B579393C01
0.438,0.75 0.552,0.563 false 0.49,1.438 0.854,1.417 true 0.344,0.74 0.656,0.938 0.313,0.198 10 false *a 0.323,1.354 0.635,1.552 0.313,0.198 10 false *a
*a Lock Lever


Disengage the claws and pull up the lock levers to disconnect the 2 connectors as shown in the illustration.



f.
B579394

Disconnect the 5 connectors.


g.
B579395C01
1,0.708 0.74,0.406 true 0.521,0.313 0.708,0.49 0.188,0.177 10 true *a
*a Protective Tape


Remove the 2 nuts.


h.

Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.


i.

Pull out the instrument panel junction block assembly with multiplex network body ECU.


j.
B579396

Disengage the claws.


k.
B579397C01
2.25,0.719 2.396,0.573 false 2.323,1.458 2.688,1.417 true 2.146,0.698 2.458,0.896 0.313,0.198 10 false *a 2.156,1.375 2.469,1.573 0.313,0.198 10 false *a
*a Lock Lever


Disengage the claws and pull up the lock levers to disconnect the 2 connectors as shown in the illustration.


l.

Disconnect the connector.


m.

Remove the instrument panel junction block assembly with multiplex network body ECU.


Hide 82715 6.REMOVE WIRING HARNESS CLAMP BRACKET

a.
B579399

Remove the bolt.


b.

Disengage the guides to remove the wiring harness clamp bracket.


Hide 89221 7.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

a.
E438385C01
0.677,1.146 0.875,1.365 true 0.208,1.052 0.583,1.052 true 0.906,1.302 1.219,1.5 0.313,0.198 10 false *1 0.01,0.958 0.323,1.156 0.313,0.198 10 false *2
*1 Instrument Panel Junction Block Assembly
*2 Main Body ECU (Multiplex Network Body ECU)
V100135

Push


Press the claw of the instrument panel junction block assembly as shown in the illustration to release the lock.


b.
E438386C01
1.542,1.708 1.729,1.479 true 1.427,1.698 1.74,1.854 0.313,0.156 10 false *a
*a Protective Tape
V100135

Insert
V113147

Raise in this Direction


With the instrument panel junction block assembly lock released, insert a screwdriver with its tip wrapped in protective tape horizontally between the main body ECU (multiplex network body ECU) and the instrument panel junction block assembly.

NOTICE:
·

Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).

·

Do not insert the screwdriver under the connector socket of the main body ECU (multiplex network body ECU).




c.

Using the screwdriver, carefully raise the main body ECU (multiplex network body ECU) to the position where the connector becomes disconnected.

NOTICE:

Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).



d.
E438387C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the main body ECU (multiplex network body ECU) as shown in the illustration.

NOTICE:

Do not touch the main body ECU (multiplex network body ECU) connector.