Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › from 2021.04
RM36W0E _56 Audio / Visual / Telematics _091907 TELEMATICS _0434308 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B15C464  Airbag Signal Signal Plausibility Failure  


DESCRIPTION

If the telephone transceiver assembly detects an error in communication between the telephone transceiver assembly and the airbag sensor assembly as a result of the telephone transceiver assembly self check, this DTC will be set.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C464 Airbag Signal Signal Plausibility Failure Telephone transceiver assembly detects an error in signals from airbag sensor assembly when ignition switch is ON.
·

Airbag system

·

Harness or connector

·

Airbag sensor assembly

·

Telephone transceiver assembly



WIRING DIAGRAM

B469621E50
1.969,1.073 2.438,1.25 0.469,0.177 10 false GSW3 4.885,1.073 5.323,1.26 0.438,0.188 10 false GSW 1.115,2.063 1.469,2.354 0.354,0.292 10 false H14 1.115,2.229 2.927,2.448 1.813,0.219 10 false Airbag Sensor Assembly 4.448,2.052 5.167,2.271 0.719,0.219 10 false H85 4.448,2.219 6.583,2.521 2.135,0.302 10 false Telephone Transceiver Assembly 2.5,1.094 2.76,1.365 0.26,0.271 10 false 23 4.604,1.094 4.771,1.271 0.167,0.177 10 false 13

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Before replacing the telematics transceiver assembly, refer to Service Bulletin.



PROCEDURE

1.CLEAR DTC (AIRBAG SYSTEM)
a.

Clear the DTCs.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

2.CHECK DTC (AIRBAG SYSTEM)
2.CHECK DTC (AIRBAG SYSTEM)
a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Check for DTCs and check that no DTCs are output.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.CLEAR DTC

B

3.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

Result:
Proceed to
NEXT



NEXT

4.CHECK DTC
4.CHECK DTC
a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459

Result:
Result Proceed to
DTCs are not output A
DTC B15C464 is output B



A

B

5.CHECK TELEPHONE TRANSCEIVER ASSEMBLY (GSW SIGNAL)
5.CHECK TELEPHONE TRANSCEIVER ASSEMBLY (GSW SIGNAL)
a.
E422011C42
1.469,0.219 1.948,0.458 0.479,0.24 1.167,1.094 0.677,0.375 true 0.135,0.104 0.406,0.365 0.271,0.26 10 false *a 0.302,0.281 0.677,0.427 0.375,0.146 10 false GSW 1.563,0.26 2,0.51 0.438,0.25 10 false H85 0.208,4.031 0.646,4.292 0.438,0.26 10 false GND
*a Component with harness connected
(Telephone Transceiver Assembly)


Remove the telephone transceiver assembly but do not disconnect the connectors.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



b.

Check the input waveform.

i.

Check the signal waveform according to the condition(s) in the table below. (Check the waveform from the back of the wire harness connector of the telephone transceiver assembly while the airbag sensor assembly connectors are connected.)

Reference Waveform:
Item Condition
Tester connection H85-13 (GSW) - Body ground
Tool setting 5.0 V/DIV., 20 ms/DIV.
Vehicle condition Ignition switch ON


OK:

The waveform is similar to that shown in the illustration.




Result:
Proceed to
OK
NG



OK

6.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - AIRBAG SENSOR ASSEMBLY)
6.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


NOTICE:
·

The ignition switch must be off.

·

Do not exchange the telephone transceiver assembly with one from another vehicle.




Result:
Proceed to
NEXT



NEXT

7.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the H85 telephone transceiver assembly connector.


b.

Disconnect the H14 airbag sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H85-13 (GSW) - H14-23 (GSW3) Always Below 1 Ω
H85-13 (GSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE HARNESS OR CONNECTOR