Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2020.09
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440901 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  VEHICLE CONTROL HISTORY  


DESCRIPTION


·

Vehicle Control History is a function that captures and stores ECU data when triggered by specific vehicle behavior.

·

It may be possible to determine the cause of the malfunction by checking the vehicle history information and freeze frame data.

·

The number of possible stored Freeze Frame Data sets, whether multi Freeze Frame Data is available, the number of freeze frame points, Freeze Frame Data items, the ECU internal range, etc., is different depending on the stored group.

·

The stored data items for Vehicle Control History Freeze Frame Data are different depending on the stored group. When the value of a data item does not change across all points, only the value of the detection point will be displayed. The contents of the Freeze Frame Data is almost the same as that of the Data List.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>DATA LIST / ACTIVE TEST



PRECAUTIONS


·

As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save Vehicle Control History before performing any inspections.

·

As Vehicle Control History may be stored when performing an Active Test, learning, etc., make sure to clear the Vehicle Control History before returning the vehicle to the customer.



CHECK VEHICLE CONTROL HISTORY (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Operate the GTS to enter the Vehicle Control History (RoB).

Chassis > Brake > Utility
Tester Display
Vehicle Control History (RoB)
50005 435 55
Vehicle Control History Item
Code Tester Display Measurement Item User Notification Diagnostic Note RoB Output from
X0455 Steering Angle Sensor Wrong Installation History of steering angle sensor being installed incorrectly Slip indicator light illuminates Refer to Steering Angle Sensor Wrong Installation (X0455).
(Click here)
Brake
X204C Zero Point Calibration of Yaw Rate Sensor Undone History of incomplete yaw rate sensor zero point calibration Slip indicator light illuminates Refer to Zero Point Calibration of Yaw Rate Sensor Undone (X204C).
(Click here)
Brake
X2079 Communication Error from Brake Control Module to Engine Control Module History of being unable to send data to the ECM continuously for 2 seconds or more Slip indicator light illuminates
1.

Using the GTS, perform a Health Check.

2.

Proceed to related output DTC or vehicle control history (RoB).


Brake
X2086 SRS Airbag Malfunction History of receiving a malfunction signal output for a secondary collision brake control request from the airbag sensor assembly 2 consecutive times - Refer to How to Proceed with Troubleshooting in Airbag System.
(Click here)
Brake
X2087 Engine Malfunction History of receiving an SFI system malfunction signal continuously from the ECM for 1 second or more Slip indicator light illuminates Refer to How to Proceed with Troubleshooting in SFI System.
(Click here)
Brake
X2088 Bank Angle Detected History of VSC operation being temporarily prohibited when driving at a steep bank angle, etc. Slip indicator light illuminates Explain that VSC operation was temporarily prohibited when driving on a road with a steep bank angle, etc. Brake
X208A Zero Point Calibration of Steering Angle Sensor Initialization Malfunction History of being unable to obtain the steering angle zero point after driving at a vehicle speed exceeding 15 km/h (9 mph) for 0.05 seconds or more Slip indicator light illuminates Perform steering angle sensor zero point calibration. Brake
X2096 Pre-Collision Brake History of pre-collision brake operation In accordance with Pre-collision System behavior - Brake
X2098 Pre-Collision Brake Assist History of pre-collision brake assist operation In accordance with Pre-collision System behavior - Brake
X20A0 ABS History of ABS operation Slip indicator light blinks - Brake
X20A1 VSC History of VSC operation Slip indicator light blinks - Brake
X20A2 TRC(TRAC) History of TRC operation Slip indicator light blinks - Brake
X20A7 Brake Assist History of brake assist operation - - Brake
X20A8 Secondary Collision Brake History of secondary pre-collision brake operation - - Brake
X20D7 Zero Point Calibration of Steering Angle Sensor Malfunction History of the steering angle sensor zero point calibration position differing from the stored value Slip indicator light illuminates Refer to Zero Point Calibration of Steering Angle Sensor Malfunction (X20D7).
(Click here)
Brake
X20D8 Zero Point Calibration of Steering Angle Sensor Not Acquired History of being unable to obtain the steering angle zero point Slip indicator light illuminates Refer to Zero Point Calibration of Steering Angle Sensor Not Acquired (X20D8).
(Click here)
Brake
X261B Software Inconsistency with PCS Module History of mismatch between the specification information sent by the PCS function and the specification information stored in the skid control ECU (brake actuator assembly) -
1.

Using the GTS, perform a Health Check.

2.

Proceed to related output DTC or vehicle control history (RoB).


Brake



CLEAR VEHICLE CONTROL HISTORY (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Operate the GTS to enter the Vehicle Control History (RoB).

Chassis > Brake > Utility
Tester Display
Vehicle Control History (RoB)
50005 435 55

f.

Press the DTC clear button.

NOTICE:

By performing this procedure, all stored Vehicle Control History items will be cleared.




CHECK VEHICLE CONTROL HISTORY (STEERING ANGLE SENSOR)


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Operate the GTS to enter the Vehicle Control History (RoB).

Chassis > Steering Angle Sensor > Utility
Tester Display
Vehicle Control History (RoB)
50005 445 55
Code Tester Display Measurement Item User Notification Diagnostic Note
XF01B ECU Security Key Not Registered ECU security key has not been registered * (Click here)

*: Receive side ECU detects communication malfunction and may operate warning in multi-information display or indicator light.




CLEAR VEHICLE CONTROL HISTORY (STEERING ANGLE SENSOR)


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Operate the GTS to enter the Vehicle Control History (RoB).

Chassis > Steering Angle Sensor > Utility
Tester Display
Vehicle Control History (RoB)
50005 445 55

f.

Press the DTC clear button.

NOTICE:

By performing this procedure, all stored Vehicle Control History items will be cleared.




CHECK VEHICLE CONTROL HISTORY (AIRBAG SYSTEM)


HINT:

A part of the control history can be confirmed using the vehicle control history.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>VEHICLE CONTROL HISTORY