Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type without TAS Type) › from 2021.04
RM36W0E _56 Audio / Visual / Telematics _088597 AUDIO / VIDEO _0475154 AUDIO AND VISUAL SYSTEM(for Radio and Display Type without TAS Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type without TAS Type)  Mute Signal Circuit between Stereo Component Equalizer and Telematics Transceiver  


DESCRIPTION

The telephone transceiver assembly sends a mute signal to the stereo component equalizer assembly.

The stereo component equalizer assembly controls the volume according to the mute signal from the telephone transceiver assembly.

WIRING DIAGRAM

E463321E02
1.323,1.885 3.104,2.344 1.781,0.458 10 false Stereo Component Equalizer Assembly 1.323,1.729 3.292,1.969 1.969,0.24 10 false O131 4.385,1.698 4.75,1.927 0.365,0.229 10 false H85 4.385,1.865 5.781,2.344 1.396,0.479 10 false Telephone Transceiver Assembly 4.635,1.135 5.24,1.333 0.604,0.198 10 false MUTE 4.344,1.031 4.615,1.271 0.271,0.24 10 false 14 2.604,1.021 2.875,1.26 0.271,0.24 10 false 4 2.094,1.146 2.583,1.354 0.49,0.208 10 false TMUT

CAUTION / NOTICE / HINT

NOTICE:

When replacing the telephone transceiver assembly, make sure to replace it with a new one.


HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type without TAS Type)>PRECAUTION


PROCEDURE

1.CHECK TELEPHONE TRANSCEIVER ASSEMBLY
a.
E442862C05
1.521,0.594 2.021,0.844 0.5,0.25 1.052,1.698 0.781,0.99 true 1.635,0.625 2.063,0.854 0.427,0.229 10 false H85 0.604,0.781 1.052,1.021 0.448,0.24 10 false MUTE 0.198,0.177 0.51,0.375 0.313,0.198 10 false *a
*a Component with harness connected
(Telephone Transceiver Assembly)


Remove the telephone transceiver assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H85-14 (MUTE) - Body ground Ignition switch ON, audio system playing
→ Emergency call mode
2.0 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT EQUALIZER ASSEMBLY - TELEPHONE TRANSCEIVER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT EQUALIZER ASSEMBLY - TELEPHONE TRANSCEIVER ASSEMBLY)
a.

Disconnect the O131 stereo component equalizer assembly connector.


b.

Disconnect the H85 telephone transceiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O131-4 (TMUT) - H85-14 (MUTE) Always Below 1 Ω
O131-4 (TMUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK STEREO COMPONENT EQUALIZER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK STEREO COMPONENT EQUALIZER ASSEMBLY
a.

Disconnect the H85 telephone transceiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H85-14 (MUTE) - Body ground Ignition switch ON 2.0 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPLACE STEREO COMPONENT EQUALIZER ASSEMBLY