When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, lane tracing assist system, road sign assist system, pre-collision system, forward recognition camera system or auto high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.
56111
1.CLEAN WINDSHIELD GLASS
When reusing the windshield glass:
Using a scraper, remove any remaining adhesive dam and adhesive residue from the windshield glass.
Be careful not to damage the windshield glass.
Clean the outer circumference of the windshield glass with a non-residue solvent.
Do not touch the windshield glass surface after cleaning it.
Even if using a new windshield glass, clean it with a non-residue solvent.
56116C
2.INSTALL NO. 2 WINDSHIELD GLASS STOPPER
Using a brush or sponge, coat the installation area of the 2 No. 2 windshield glass stoppers with primer G.
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
for Type A:
Install 2 new No. 2 windshield glass stoppers to the windshield glass as shown in the illustration.
| *a | Back Side of Windshield Glass | *b | Ceramic Notch |
| *c | Windshield Glass Edge Side | - | - |
| Area | Dimension |
|---|---|
| a | 14.4 to 15.4 mm (0.567 to 0.606 in.) |
| b | 40 mm (1.57 in.) |
Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.
for Type B:
Install 2 new No. 2 windshield glass stoppers to the windshield glass as shown in the illustration.
| *a | Back Side of Windshield Glass | *b | Ceramic Notch |
| *c | Windshield Glass Edge Side | - | - |
| Area | Dimension |
|---|---|
| a | 14.4 to 15.4 mm (0.567 to 0.606 in.) |
| b | 40 mm (1.57 in.) |
Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.
56115A
3.INSTALL NO. 1 WINDSHIELD GLASS STOPPER
Install 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.
Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.
56117A
4.INSTALL WINDOW GLASS ADHESIVE DAM
Using a brush or sponge, coat the installation area of the window glass adhesive dam with primer G.
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
| *a | Back Side of Windshield Glass |
| *b | Ceramic Notch |
Install a new window glass adhesive dam to the windshield glass as shown in the illustration.
75533G
5.INSTALL WINDSHIELD OUTSIDE MOULDING
Using a brush or sponge, coat the installation area of the windshield outside moulding with primer G.
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
Install a new windshield outside moulding to the windshield glass as shown in the illustration.
| *a | Back Side of Windshield Glass | *b | Ceramic Notch |
| Area | Dimension |
|---|---|
| a | 1.15 to 2.65 mm (0.0453 to 0.104 in.) |
56111
6.INSTALL WINDSHIELD GLASS
Clean and shape the contact surface of the vehicle body.
|
Adhesive |
Using a knife, cut away excess adhesive on the contact surface of the vehicle body as shown in the illustration.
Leave as much adhesive on the vehicle body as possible.
Clean the contact surface of the vehicle body with a piece of cloth saturated with non-residue solvent.
Position the windshield glass.
Using suction cups, place the windshield glass in the correct position.
Check that the whole contact surface of the windshield glass rim is perfectly even.
| *a | Matchmark |
Align the matchmarks on the windshield glass and vehicle body.
Check that the windshield glass stoppers are engaged to the vehicle body correctly.
Remove the windshield glass.
Using a brush, coat the installation surface on the vehicle body with primer M.
Do not coat the adhesive with primer M.
Do not apply too much primer M.
Allow the primer M to dry for 3 minutes or more.
Throw away any leftover primer M.
If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.
Using a brush or sponge, coat the adhesive application area with primer G.
| *1 | Window Glass Adhesive Dam | - | - |
| *a | Back Side of Windshield Glass | - | - |
|
Primer G | - | - |
| Area | Dimension |
|---|---|
| a | 11 mm (0.433 in.) or more |
| b | 11 mm (0.433 in.) or more |
| c | 11 mm (0.433 in.) or more |
| d | 19 mm (0.748 in.) or more |
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
Apply primer G to the ceramic notches.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
Apply adhesive to the windshield glass.
Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent
| *a | Cartridge Nozzle |
|
Adhesive |
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 12 to 15 mm (0.472 to 0.591 in.) |
| b | 8.0 to 11 mm (0.315 to 0.433 in.) |
Load the sealer gun with the cartridge.
Apply adhesive to the windshield glass as shown in the illustration.
| *1 | Window Glass Adhesive Dam | - | - |
| *a | Back Side of Windshield Glass | - | - |
|
Adhesive | - | - |
| Area | Dimension |
|---|---|
| a | 8.0 to 11 mm (0.315 to 0.433 in.) |
| b | 8.0 to 11 mm (0.315 to 0.433 in.) |
| c | 8.0 to 11 mm (0.315 to 0.433 in.) |
| d | 8.0 mm (0.315 in.) |
Install the windshield glass.
| *a | Matchmark |
Using suction cups, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.
Check that the windshield glass stoppers are engaged to the vehicle body correctly.
Check the clearance between the vehicle body and windshield glass.
Lightly press the outer surface of the windshield glass to ensure that the windshield glass is securely fit to the vehicle body.
Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.
Using a scraper, remove any excess or protruding adhesive.
Hold the windshield glass using protective tape until the applied adhesive becomes hard.
Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.
7.INSPECT FOR LEAK
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
63311C
8.INSTALL ROOF HEADLINING
Return the front section of the roof headlining to its original position.
74612
9.INSTALL ASSIST GRIP COVER
74610A
10.INSTALL ASSIST GRIP SUB-ASSEMBLY
74348C
11.INSTALL VISOR HOLDER
74320
12.INSTALL VISOR ASSEMBLY LH
74310
13.INSTALL VISOR ASSEMBLY RH
Use the same procedure as for the LH side.
81260A
14.INSTALL MAP LIGHT ASSEMBLY
62212
15.INSTALL FRONT PILLAR GARNISH LH
62211
16.INSTALL FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
62312B
17.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Install the front door opening trim weatherstrip LH.
62311B
18.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
87810
19.INSTALL INNER REAR VIEW MIRROR ASSEMBLY
w/o EC Mirror:
Click hereVehicle Interior>MIRROR (INT)>INNER REAR VIEW MIRROR (w/o EC Mirror)>INSTALLATION
w/ EC Mirror:
Click hereVehicle Interior>MIRROR (INT)>INNER REAR VIEW MIRROR (w/ EC Mirror)>INSTALLATION
86401
20.INSTALL FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY
8646C
21.INSTALL FORWARD RECOGNITION CAMERA
22.INSTALL WINDSHIELD WIPER MOTOR AND LINK
8646C
23.ADJUST FORWARD RECOGNITION CAMERA
If the forward recognition camera has been replaced with a new one or the windshield glass has been removed and installed, it is necessary to perform Forward Recognition Camera Learning.
Forward Recognition Camera Learning can be performed by using either Target Adjustment (One Time Recognition) or Target Adjustment (Sequential Recognition) or Driving Adjustment.
Target Adjustment (One Time Recognition):
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)
Target Adjustment (Sequential Recognition):
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)
Driving Adjustment:
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT