Home › Power Source / Network › POWER DISTRIBUTION › FUSIBLE LINK (for 120A DC/DC) › 2020.03–2020.07
RM36W0E _57 Power Source / Network _088265 POWER DISTRIBUTION _0489972 FUSIBLE LINK(for 120A DC/DC) A

POWER DISTRIBUTION  FUSIBLE LINK(for 120A DC/DC)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the engine room fusible link removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 82662A 3.REMOVE NO. 1 RELAY BLOCK COVER

Hide 28371 4.REMOVE NO. 1 IGNITION RELAY

a.
E471058

Remove the No. 1 ignition relay.


Hide 85948 5.REMOVE WINDSHIELD WIPER RELAY

a.
E471059

Remove the windshield wiper relay.


Hide 85912K 6.REMOVE VVT RELAY

a.
E471060

Remove the VVT relay.


Hide 89730A 7.REMOVE SECURITY WARNING RELAY

a.
E471061

Remove the security warning relay.


Hide 82663 8.REMOVE RELAY BLOCK LOWER COVER

a.
E471062

Remove the nut.


b.
E471063

Disconnect the 2 connectors.


c.
E471064C01
1.469,0.833 1.167,1.083 true 0.958,0.99 1.177,1.198 0.219,0.208 10 true *a
*a Protective Tape
V113147

Separate in this Direction


Using a screwdriver with its tip wrapped in protective tape, disengage the claws to separate the wire harness as shown in the illustration.


d.
E471065

for RHD:

i.

Disengage the clamps to separate the wire harness.



e.
E471066

Remove the 2 bolts and nut.


f.
E471067C01
2.25,0.833 2.677,0.667 true 2.708,0.563 2.948,0.771 0.24,0.208 10 true *1
*1 Engine Room Relay Block Assembly


Disengage the guides to separate the engine room relay block assembly.


g.
E471068

Disengage the clamp to separate the wire harness.


h.
E471069C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the engine room relay block as shown in the illustration.


i.
E471071

Remove the wire harness repair tapes.


j.
E471072

Disengage the claws to separate the relay block lower cover.


k.
E471073C01
0.875,0.854 0.625,1.135 true 0.406,1.083 0.625,1.302 0.219,0.219 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, disengage the claws to separate the wire harness.


l.

Remove the relay block lower cover.


Hide 82610A 9.SEPARATE FUSE BLOCK ASSEMBLY

a.
E471074C01
2.354,1.115 1.99,0.854 true 2.365,1.031 2.594,1.229 0.229,0.198 10 true *a
*a Protective Tape
V113147

Separate in this Direction


Using a screwdriver with its tip wrapped in protective tape, disengage the claws to separate the wire harness as shown in the illustration.


b.
E471075

Remove the vinyl tape.


c.
E471076C01
0,0 0,0 false
V113147

Move in this Direction


Move the engine room relay block as shown in the illustration.


d.
E471077C01
0.813,1.031 1.333,0.906 true 0.563,0.938 0.802,1.146 0.24,0.208 10 true *a
*a Protective Tape
V113147

Separate in this Direction


Using a screwdriver with its tip wrapped in protective tape, disengage the claws to separate the fuse block assembly as shown in the illustration.


Hide 82210P 10.REMOVE ENGINE ROOM FUSIBLE LINK

a.
E471078C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the 2 bolts and engine room fusible link as shown in the illustration.