Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING ECU (for RHD) › from 2021.11
RM36W0E _55 Steering _087549 POWER ASSIST SYSTEMS _0432877 POWER STEERING ECU(for RHD) A

POWER ASSIST SYSTEMS  POWER STEERING ECU(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the power steering ECU assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Power steering ECU assembly Update ECU security key Vehicle control history (RoB) are stored (Click here)
Assist map writing
·

DTCs are stored

·

EPS warning light illuminates


(Click here)
Steering sensor (Including removal and installation)
·

Steering angle neutral point

·

Adjust steering angle setting


Parking assist monitor system (Click here)
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system *1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.REMOVE STEERING COLUMN ASSEMBLY

Hide 45020B 2.REMOVE STEERING LOCK ACTUATOR ASSEMBLY (w/ Entry and Start System)

Hide 89650 3.REMOVE POWER STEERING ECU ASSEMBLY

NOTICE:
·

Do not drop the power steering ECU assembly, strike it with tools or subject it to impacts.

·

If the power steering ECU assembly is subjected to an impact, replace it with a new one.

·

Do not pull the wire harness of the electric power steering column sub-assembly.

·

Do not allow any moisture to come into contact with the power steering ECU assembly.

·

Do not loosen any bolts not mentioned in the procedure.

·

Do not allow any foreign matter to contaminate the power steering ECU assembly.



a.
C433970

Disconnect the connector.


b.

Disengage the clamp.


c.

for TMC Made:

i.
C433971

Remove the bolt and harness bracket from the electric power steering column sub-assembly.



d.

for TMMF, TMMCZ Made:

i.
C436913

Using a T40 "TORX" socket wrench, remove the bolt and harness bracket from the electric power steering column sub-assembly.



e.

for TMC Made:

i.
C433972

Remove the 2 bolts and power steering ECU assembly from the electric power steering column sub-assembly.



f.

for TMMF, TMMCZ Made:

i.
C436914

Using a T40 "TORX" socket wrench, remove the 2 bolts and power steering ECU assembly from the electric power steering column sub-assembly.



Hide 45254B 4.REMOVE ELECTRIC POWER STEERING MOTOR SHAFT DAMPER

a.
C433973

Remove the electric power steering motor shaft damper from the electric power steering column sub-assembly.