Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY › from 2020.09
RM36W0E _55 Steering _087550 STEERING COLUMN _0424130 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the electric power steering column sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Electric power steering column sub-assembly Assist map writing There is a difference in steering effort between turning left and right. (Click here)
Steering lock ECU (Steering lock actuator assembly) Code registration
for HV Model:
·

Wireless door lock control system (w/ Entry and Start System)

·

Entry and start system (for Entry function, HV model)

·

Entry and start system (for Start function, HV model)

·

Hybrid control system cannot be started


for Gasoline Model:
·

Wireless door lock control system (w/ Entry and Start System)

·

Entry and start system (for Entry function, Gasoline model)

·

Entry and start system (for Start function, Gasoline model)

·

Engine start function


See Service Bulletin for the registration method

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system *1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for the RHD and LHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45130 3.REMOVE HORN BUTTON ASSEMBLY

Hide 45100 4.REMOVE STEERING WHEEL ASSEMBLY

Hide 45287 5.REMOVE LOWER STEERING COLUMN COVER

NOTICE:

Removing the lower steering column cover in the incorrect order will cause the parts to break.


a.

Release the tilt and telescopic lever and fully extend and lower the steering column assembly.


b.

Lock the tilt and telescopic lever.


c.
C436919

Remove the 3 screws.


d.
C436920C01
0,0 0,0 false
V100135

Push
V100155

Push Area


While pressing the push area shown in the illustration to disengage the claws, slightly lower the lower steering column cover.


Hide 45286B 6.REMOVE UPPER STEERING COLUMN COVER

a.
C436921

Disengage the claw to remove the upper steering column cover.


Hide 7.REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the ignition switch ON.

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the auxiliary battery connected and the ignition switch ON.

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.



a.

Disconnect each connector from the turn signal switch assembly with spiral cable sub-assembly.


b.
C436922C01
0.906,0.448 1.198,0.448 false 0.74,0.333 1.052,0.49 0.313,0.156 10 false *a
*a Clamp


Using pliers, expand the clamp.


c.

While holding the clamp expanded, raise the claw using a screwdriver to disengage it, and then remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.


Hide 58810J 8.REMOVE FRONT CONSOLE BOX SUB-ASSEMBLY (for 5 Door)

Hide 58810J 9.REMOVE CONSOLE BOX ASSEMBLY (for 3 Door)

Hide 67914B 10.REMOVE FRONT DOOR SCUFF PLATE LH (for 5 Door)

Hide 67914B 11.REMOVE FRONT DOOR SCUFF PLATE LH (for 3 Door)

Hide 62112 12.REMOVE COWL SIDE TRIM BOARD LH

Hide 55606 13.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 62312B 14.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 55317E 15.REMOVE NO. 1 INSTRUMENT SIDE PANEL

Hide 53601 16.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 55480D 17.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Hide 84340 18.REMOVE STOP LIGHT SWITCH ASSEMBLY

Hide 45259A 20.REMOVE COLUMN HOLE COVER SILENCER SHEET (for LHD)

a.
C436923

Remove the retainer.


b.

Disengage the clip to remove the column hole cover silencer sheet.


Hide 45259A 21.REMOVE COLUMN HOLE COVER SILENCER SHEET (for RHD)

a.
C434148

Disengage the clips to remove the column hole cover silencer sheet.


Hide 45260 22.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C436924C01
1.875,1.521 2.344,1.521 2.344,1.521 2.344,1.885 true 1.885,1.573 2.344,1.573 true 2.271,1.896 2.51,2.104 0.24,0.208 10 true *a
*a Matchmark
V113147

Disconnect in this direction


Put matchmarks on the No. 2 steering intermediate shaft assembly and steering gear assembly.


b.

Remove the bolt.


c.

Disconnect the No. 2 steering intermediate shaft assembly from the steering gear assembly.


Hide 45260 23.REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C436925C01
2.438,0.74 1.719,0.74 true 1.729,0.802 1.969,0.802 1.969,0.802 1.969,0.75 true 2.458,0.635 2.667,0.823 0.208,0.188 10 true *a
*a Matchmark
V113147

Remove in this direction


Put matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.


b.

Remove the bolt.


c.

Remove the No. 2 steering intermediate shaft assembly from the steering column assembly.


Hide 24.REMOVE STEERING COLUMN ASSEMBLY

a.

Disconnect each connector and disengage each wire harness clamp from the steering column assembly.


b.
C436926

Remove the bolt, 2 nuts and steering column assembly.