Home › Drivetrain › P910 (HYBRID TRANSMISSION / TRANSAXLE) › SHIFT LEVER (for TMMF, TMMCZ Made) › from 2021.11
RM36W0E _52 Drivetrain _088636 P910 HYBRID TRANSMISSION / TRANSAXLE _0492210 SHIFT LEVER(for TMMF, TMMCZ Made) A

P910 HYBRID TRANSMISSION / TRANSAXLE  SHIFT LEVER(for TMMF, TMMCZ Made)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RHD and LHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 1.INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY

a.
C435113N01
0.667,1.74 0.823,1.938 0.156,0.198 10 true 1 0.76,0.458 0.917,0.656 0.156,0.198 10 true 3 2.521,1.729 2.677,1.927 0.156,0.198 10 true 4 2.448,0.49 2.604,0.688 0.156,0.198 10 true 2

Temporarily install the transmission floor shift assembly to the vehicle body with the 4 bolts.


b.

Fully tighten the 4 bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


c.

Engage the 2 clamps to connect the wire harness to the transmission floor shift assembly.


d.

Connect the connector.


e.

Engage the clamp to connect the wire harness to the transmission floor shift assembly.


f.

Connect the shift lock control ECU connector.


Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:

Before connecting the transmission control cable assembly, check that the shift lever is in N.


a.
C400603C08
2.458,1.573 2.021,1.021 false 2.01,1.667 1.625,1.177 false 2.448,1.573 2.76,1.729 0.313,0.156 10 false *1 2,1.677 2.313,1.833 0.313,0.156 10 false *2
*1 Adjuster Case
*2 Adjuster Case Cover


Slide the adjuster case cover in the direction shown by the arrow.


b.
C400817C07
2.688,1.74 2.177,1.063 false 2.24,1.771 1.865,1.219 false 2.688,1.74 3,1.896 0.313,0.156 10 false *1 2.24,1.781 2.552,1.938 0.313,0.156 10 false *2
*1 Adjuster Case
*2 Lock Piece


Using a precision screwdriver, pull out the lock piece of the adjuster case.


c.
C400818C03
0.448,1.208 0.625,1.208 0.625,1.208 1.729,1.49 true 2.188,1.26 2.896,2.208 2.896,2.208 2.208,3.479 true 0.26,1.115 0.573,1.271 0.313,0.156 10 false *1 2.01,0.365 2.323,0.521 0.313,0.156 10 false *a 2.948,2.104 3.26,2.26 0.313,0.156 10 false *2
*1 Lock Nut
*2 Stopper
*a Push in


Turn the lock nut of the transmission control cable assembly counterclockwise. While holding the lock nut, push in the stopper.


d.
C435107C01
0.771,1.104 0.531,0.979 false 2.604,1.021 2.365,0.896 false 0.344,0.896 0.656,1.052 0.313,0.156 10 false *1 2.208,0.813 2.521,0.969 0.313,0.156 10 false *1
*1 Stopper


Connect the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

After installation, check that the outer part of the stopper is as shown in the illustration.

·

Do not forcibly pull the floor shift transmission control select cable into the cabin.




e.
C435108

Connect the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Push the end of the transmission control cable assembly all the way to the base of the transmission floor shift assembly pin.

·

Connect the transmission control cable assembly so that the lock piece faces the driver side.

·

Before connecting the floor shift transmission control select cable, check that the shift lever is in N.




f.
C435105C02
1.875,0.74 2.26,0.958 true 2.521,1.031 2.938,1.302 true 2.979,1.198 3.198,1.375 0.219,0.177 10 true *1 1.635,0.625 1.854,0.813 0.219,0.188 10 true *2
*1 Lock Piece
*2 Adjuster Case


Push in the lock piece of the adjuster case to lock it.

NOTICE:
C414647C05
1.271,0.333 1.604,0.333 false 2.333,1.667 2.583,1.167 2.583,1.167 2.75,1.167 true 2.781,1.063 3.094,1.219 0.313,0.156 10 false *1 1.646,0.24 1.958,0.396 0.313,0.156 10 false *2
*1 Transmission Control Cable Assembly
*2 Lever Shaft


·

When pushing in the lock piece of the adjuster case to lock it, remove your hand from the lever shaft.

·

When pushing in the lock piece of the adjuster case to lock it, do not move the lever shaft or transmission control cable assembly forward or backward.




g.
C435106C02
2.344,1.094 2.719,1.458 true 2.458,0.917 2.719,0.573 true 2.667,1.469 2.875,1.656 0.208,0.188 10 true *1 2.75,0.469 3,0.646 0.25,0.177 10 true *2
*1 Adjuster Case Cover
*2 Adjuster Case


Move the adjuster case cover in the direction shown by the arrow.

NOTICE:

If the adjuster case cover is not moved far enough so that the adjuster case cover engages the lock piece, the cable will not be able to lock, and reliable shift operation will not be possible.



Hide 58910C 3.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 33554 5.INSTALL SHIFT LEVER CAP

a.

Engage the 2 claws to install the shift lever cap to the position indicator housing.