Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF, TMMCZ Made) › from 2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0494153 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF, TMMCZ Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF, TMMCZ Made)  C050C12  Left Rear Wheel Speed Sensor Circuit Short to Battery  


DESCRIPTION

Each speed sensor detects wheel speed and sends signals to the skid control ECU (brake actuator assembly). These signals are used by the ABS control.

The speed sensor detects the magnetic fields of the speed sensor rotor as it rotates and outputs a pulse signal.

The frequency of the pulse varies in accordance with the rotational speed of the speed sensor rotor and the system uses this to determine the wheel speed.

HINT:

The following example shows a pulse signal that is output when the wire harness connectors are connected to the speed sensors and skid control ECU (brake actuator assembly).


C151818E70
1.594,0.854 1.594,0.469 1.594,0.469 1.688,0.469 false 1.74,0.385 2.656,0.625 0.917,0.24 10 false Speed Sensor 4.021,2.115 4.719,2.365 0.698,0.25 10 false Low speed 4.99,2.115 5.729,2.354 0.74,0.24 10 false High speed 0.969,2.177 2.25,2.406 1.281,0.229 10 false Speed Sensor Rotor

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C050C12 Left Rear Wheel Speed Sensor Circuit Short to Battery A short to +B in the speed sensor signal circuit is detected for 0.12 seconds or more.
·

Rear speed sensor LH (rear axle hub and bearing assembly LH)

·

Wire harness or connector

·

Skid control sensor wire LH (No. 2 parking brake wire assembly)

·

Skid control ECU (brake actuator assembly)


Brake

WIRING DIAGRAM

C393355E88
0.604,2.323 2.01,3.156 1.406,0.833 10 false Rear Speed Sensor LH (Rear Axle Hub and Bearing Assembly LH) 2.271,2.323 4.042,3.042 1.771,0.719 10 false Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly) 5.281,3.177 6.823,3.573 1.542,0.396 10 false Skid Control ECU (Brake Actuator Assembly) 5.292,1.01 5.75,1.208 0.458,0.198 10 false RL+ 3.24,1.146 3.698,1.344 0.458,0.198 10 false RL+ 1.635,1.125 2.094,1.323 0.458,0.198 10 false RL+ 2.448,1.135 2.906,1.333 0.458,0.198 10 false RL+ 1.635,1.833 2.094,2.031 0.458,0.198 10 false RL- 2.448,1.823 2.906,2.021 0.458,0.198 10 false RL- 3.24,1.823 3.698,2.021 0.458,0.198 10 false RL- 5.292,1.677 5.75,1.875 0.458,0.198 10 false RL- 2.063,1.135 2.521,1.333 0.458,0.198 10 false o1 2.073,1.823 2.531,2.021 0.458,0.198 10 false o1 3.615,1.104 4.021,1.323 0.406,0.219 10 false oO1 3.615,1.802 4.021,2.021 0.406,0.219 10 false oO1 2.104,1.604 2.406,1.833 0.302,0.229 10 false 1 5.281,2.99 5.74,3.188 0.458,0.198 10 false A39 2.104,0.927 2.406,1.156 0.302,0.229 10 false 2 3.708,0.917 4.01,1.146 0.302,0.229 10 false 3 3.698,1.604 4,1.833 0.302,0.229 10 false 4 4.99,1.01 5.292,1.24 0.302,0.229 10 false 39 4.979,1.688 5.281,1.917 0.302,0.229 10 false 23

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF, TMMCZ Made)>UTILITY

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF, TMMCZ Made)>TEST MODE PROCEDURE



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the o1 rear speed sensor LH (rear axle hub and bearing assembly LH) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
o1-2 (RL+) - o1-1 (RL-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

NG

2.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the oO1 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
oO1-3 (RL+) - oO1-4 (RL-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the oO1 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
oO1-4 (RL-) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the oO1 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
oO1-3 (RL+) or A39-39 (RL+) - oO1-4 (RL-) or A39-23 (RL-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR