Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for HV Model LHD) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0432221 BRAKE ACTUATOR(for HV Model LHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for HV Model LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during brake actuator assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
Skid control ECU (brake actuator assembly)
1.

Bleed air

2.

Perform "Reset Memory"

3.

Perform calibration (brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)
Operate the electric parking brake switch (electric parking brake switch assembly) Parking brake indicator light (red) blinks when the ignition switch is first turned to ON (Click here)

NOTICE:

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed. Therefore, when servicing the brake system components, do not operate the brake pedal while the auxiliary battery is connected.


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55815E 5.REMOVE FRONT NO. 1 VENTILATOR SEAL

Hide 55701J 7.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 8.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 88707 9.REMOVE SUCTION PIPE SUB-ASSEMBLY

a.
C435127C01
0,0 0,0 false
V113147

Rotate in this Direction


Remove the bolt and rotate the hook connector as shown in the illustration.


b.

Disconnect the suction pipe sub-assembly from the air conditioning unit assembly.


c.
C435128

Disengage the clamp to separate the suction pipe sub-assembly.


d.

Remove the O-ring from the suction pipe sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88710E 10.REMOVE AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

a.
C435129C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the air conditioning tube and accessory assembly from the air conditioning unit assembly.


b.
C436241

Disengage the clamp to separate the air conditioning tube and accessory assembly.


c.

Remove the O-ring from the air conditioning tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 11.REMOVE BRAKE ACTUATOR WITH BRACKET

a.
C436242C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the connector from the brake actuator assembly as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



b.
C436243C01
0.948,1.74 1.042,1.74 1.042,1.74 1.125,1.406 true 1.083,0.896 1.615,0.635 1.615,0.635 1.719,0.635 true 1.198,0.656 1.458,0.115 1.458,0.115 1.552,0.115 true 0.917,1.052 0.542,0.292 0.542,0.292 0.438,0.292 true 0.76,1.24 0.479,0.75 0.479,0.75 0.365,0.75 true 1.406,1.031 2.104,0.896 2.104,0.896 2.208,0.896 true 2.219,0.802 2.396,0.979 0.177,0.177 10 true *a 0.74,1.656 0.927,1.823 0.188,0.167 10 true *b 1.573,0.031 1.75,0.208 0.177,0.177 10 true *c 1.729,0.563 1.917,0.74 0.188,0.177 10 true *d 0.25,0.198 0.427,0.385 0.177,0.188 10 true *e 0.208,0.688 0.365,0.854 0.156,0.167 10 true *f
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH


Use tags or make a memo to identify the places to reconnect the brake lines.


c.
C436244

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.


d.
C436245C01
0,0 0,0 false
V113147

Move in this Direction


Move aside the suction pipe sub-assembly and air conditioner tube and accessory assembly as shown in the illustration.

NOTICE:

Do not apply excessive force to the suction pipe sub-assembly and air conditioner tube and accessory assembly.



e.
C436246

Remove the 2 nuts.


f.
C436247

Remove the bolt and brake actuator with bracket from the vehicle body.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Do not hold the brake actuator assembly by the connector.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Remove the brake actuator with bracket while avoiding the brake lines.



Hide 44591 12.REMOVE NO. 1 BRAKE ACTUATOR BRACKET

a.
C436248

Remove the 3 nuts and No. 1 brake actuator bracket from the brake actuator bracket assembly.

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator assembly when carrying it.




Hide 44510 13.REMOVE BRAKE ACTUATOR ASSEMBLY

a.
C436249

Remove the 3 bolts and brake actuator assembly from the brake actuator bracket assembly.

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator assembly when carrying it.




Hide 44521A 14.REMOVE NO. 1 BRAKE ACTUATOR CASE COLLAR

a.
C436250

Remove the 3 No. 1 brake actuator case collars from the brake actuator bracket cushion.


Hide 44547B 15.REMOVE BRAKE ACTUATOR BRACKET CUSHION

a.
C436251

Remove the 3 brake actuator bracket cushions from the brake actuator bracket assembly.