Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF, TMMCZ Made) › from 2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0494153 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF, TMMCZ Made) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF, TMMCZ Made)  Zero Point Calibration of Yaw Rate Sensor Undone (X204C)  


DESCRIPTION

Code Tester Display Measurement Item Trouble Area
X204C Zero Point Calibration of Yaw Rate Sensor Undone History of incomplete yaw rate sensor zero point calibration
·

Sensor installation

·

Yaw rate and acceleration sensor (airbag sensor assembly)



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF, TMMCZ Made)>UTILITY

·

After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform acceleration sensor zero point calibration and store system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF, TMMCZ Made)>UTILITY



PROCEDURE

1.CHECK FOR DTCs (HEALTH CHECK)
a.

Using the GTS, perform the Health Check.


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

2.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
a.

Perform zero point calibration of the yaw rate and acceleration sensor.

Chassis > Brake > Utility
Tester Display
Reset Memory
50005 435 4560
Chassis > Brake > Utility
Tester Display
Calibration
50005 435 4554

Result:
Proceed to
NEXT



NEXT

3.CLEAR VEHICLE CONTROL HISTORY
3.CLEAR VEHICLE CONTROL HISTORY
a.

Using the GTS, clear the Vehicle Control History.

Chassis > Brake > Utility
Tester Display
Vehicle Control History (RoB)
50005 435 55

Result:
Proceed to
NEXT



NEXT

4.CHECK VEHICLE CONTROL HISTORY
4.CHECK VEHICLE CONTROL HISTORY
a.

Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.


b.

Using the GTS, check for Vehicle Control History.

Chassis > Brake > Utility
Tester Display
Vehicle Control History (RoB)
50005 435 55

Result:
Result Proceed to
X204C is not output A
X204C is output B



A

END

B

5.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
5.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly


OK:

The sensor should be tightened to the specified torque.

The sensor is not installed in a tilted position.


Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS

NG

6.READ VALUE USING GTS
a.

Select the Data List using the GTS.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Lateral G Lateral G Min.: -25.105 m/s2, Max.: 24.908 m/s2 Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2
During turning: Changes in proportion with lateral acceleration
Forward and Rearward G Forward and rearward G Min.: -25.105 m/s2, Max.: 24.908 m/s2 During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
During acceleration/deceleration: Changes in proportion with acceleration
Yaw Rate Sensor Value Yaw rate sensor Min.: -128°/s, Max.: 127°/s Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Chassis > Brake > Data List
Tester Display
Lateral G
Forward and Rearward G
Yaw Rate Sensor Value
50003 435 25,26,29
OK:

The yaw rate and acceleration sensor (airbag sensor assembly) output value is normal.



Result:
Proceed to
OK
NG



OK

NG