Refer to DTC C050018
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| C05001F | Left Front Wheel Speed Sensor Circuit Intermittent | ·
The speed sensor signal is excessively noisy. ·
The calculated change in wheel speed is more than 980 m/s2 for 5*1 or 20*2 seconds or more. ·
The calculated change in wheel speed fluctuates between more than 500 m/s2 and less than -500 m/s2 for 5*1 or 20*2 seconds or more. ·
When the vehicle speed is low, excessive noise in the speed sensor pulse signal is detected 3 times or more within 0.005 seconds for 5*1 or 20*2 seconds or more. |
·
Front speed sensor LH ·
Front speed sensor rotor LH (front axle hub sub-assembly LH) |
Brake |
*1: The stop light switch assembly is OFF.
*2: The stop light switch assembly is ON.
After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
The front speed sensor rotor LH is incorporated into the front axle hub sub-assembly LH.
If the front speed sensor rotor LH needs to be replaced, replace the front axle hub sub-assembly LH.
Pre-procedure1
Remove the front speed sensor LH.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL
Procedure1
Check the front speed sensor LH.
The front speed sensor LH tip is free of scratches, oil, and foreign matter.
If there is oil or foreign matter on the front speed sensor LH, clean the front speed sensor LH.
If the front speed sensor LH is damaged, replace the front speed sensor LH with a new one.
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Remove the component with the front speed sensor rotor LH.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB (for TMMF, TMMCZ Made)>REMOVAL
The front speed sensor rotor LH is incorporated into the front axle hub sub-assembly LH.
If the front speed sensor rotor LH needs to be replaced, replace it together with the front axle hub sub-assembly LH.
Procedure1
Check the front speed sensor rotor LH.
The front speed sensor rotor LH is free of scratches, oil, and foreign matter.
If there is oil or foreign matter on the front speed sensor rotor LH, clean the front speed sensor rotor LH.
Do not use parts cleaner when cleaning the front speed sensor rotor LH.
If the front speed sensor rotor LH is damaged, replace the front speed sensor rotor LH with a new one.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The front speed sensor rotor LH is damaged.) | B |
| NG (There is foreign matter on the front speed sensor rotor LH.) | C |
A
B
C
Clean the front speed sensor rotor LH.
Do not use parts cleaner when cleaning the front speed sensor rotor LH.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None
Procedure1
Operate the GTS to clear the codes.
Post-procedure1
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, perform a Dealer Mode (Signal Check) inspection sensor check.
| Tester Display |
|---|
| Signal Check |
Check that speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.
Speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for front speed sensor LH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL
for front speed sensor rotor LH (front axle hub sub-assembly LH): Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB (for TMMF, TMMCZ Made)>REMOVAL
Pre-procedure1
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Procedure1
Operate the GTS to read the DTCs.
Check if the same DTC is output.
Post-procedure1
Turn the ignition switch off.
| Result | Proceed to |
|---|---|
| C05001F is not output | A |
| C05001F is output | B |
A
B
for front speed sensor LH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL
for front speed sensor rotor LH (front axle hub sub-assembly LH): Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB (for TMMF, TMMCZ Made)>REMOVAL
When cleaning the front speed sensor LH, make sure to clean the installation hole before installation.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None
Procedure1
Operate the GTS to clear the codes.
Post-procedure1
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, perform a Dealer Mode (Signal Check) inspection sensor check.
| Tester Display |
|---|
| Signal Check |
Check that speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.
Speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for front speed sensor LH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL
for front speed sensor rotor LH (front axle hub sub-assembly LH): Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB (for TMMF, TMMCZ Made)>REMOVAL
Pre-procedure1
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Procedure1
Operate the GTS to read the DTCs.
Check if the same DTC is output.
Post-procedure1
Turn the ignition switch off.
| Result | Proceed to |
|---|---|
| C05001F is not output | A |
| C05001F is output | B |
A
B
for front speed sensor LH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL
for front speed sensor rotor LH (front axle hub sub-assembly LH): Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB (for TMMF, TMMCZ Made)>REMOVAL