Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF, TMMCZ Made) › from 2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0494155 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF, TMMCZ Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF, TMMCZ Made)  C128854  Matching of ECUs Missing Calibration  


DESCRIPTION

The skid control ECU (brake actuator assembly) stores this DTC when the previously learned values in the VSC system and engine information sent from the ECM are inconsistent, or when the learning has not completed after the skid control ECU (brake actuator assembly) is replaced with a new one.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C128854 Matching of ECUs Missing Calibration ECM does not match. ECM Brake

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake actuator assembly), perform yaw rate and acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF, TMMCZ Made)>UTILITY


PROCEDURE

1.CHECK ECM OR BRAKE ACTUATOR ASSEMBLY
a.

Check if the ECM or brake actuator assembly had been replaced before the DTC was recorded.


Result:
Result Proceed to
Both the ECM and brake actuator assembly are not replaced A
The ECM is replaced B
The brake actuator assembly is replaced C



A

2.CLEAR DTC

B

4.CHECK VEHICLE TYPE

C

11.PERFORM SYSTEM VARIANT LEARNING
2.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

b.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

Post-procedure1

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC
a.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

b.

Check if the same DTC is output.


Result:
Result Proceed to
C128854 is not output A
C128854 is output B



A

B

4.CHECK VEHICLE TYPE
a.

Check the vehicle specification.


Result:
Result Proceed to
1KR-FE A
M15A-FKS B



A

5.PERFORM SYSTEM VARIANT LEARNING

B

8.PERFORM SYSTEM VARIANT LEARNING
5.PERFORM SYSTEM VARIANT LEARNING
a.

Perform system variant learning.

Chassis > Brake > Utility
Tester Display
Calibration
50005 435 4554
HINT:
·

System variant learning is automatically performed immediately after Test Mode is entered.

·

If learning has not yet been performed, the slip indicator light will remain on and DTC C128854 will be stored.

·

If system variant learning is not successful, the warning lights will not blink in the Test Mode pattern and DTC C128854 will not be cleared.




Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

b.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

Post-procedure1

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

7.RECONFIRM DTC
7.RECONFIRM DTC
a.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

b.

Check if the same DTC is output.


Result:
Result Proceed to
C128854 is not output A
C128854 is output B



A

END

B

8.PERFORM SYSTEM VARIANT LEARNING
a.

Perform system variant learning.

Chassis > Brake > Utility
Tester Display
Calibration
50005 435 4554
HINT:
·

System variant learning is automatically performed immediately after Test Mode is entered.

·

If learning has not yet been performed, the slip indicator light will remain on and DTC C128854 will be stored.

·

If system variant learning is not successful, the warning lights will not blink in the Test Mode pattern and DTC C128854 will not be cleared.




Result:
Proceed to
NEXT



NEXT

9.CLEAR DTC
9.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

b.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

Post-procedure1

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

10.RECONFIRM DTC
10.RECONFIRM DTC
a.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

b.

Check if the same DTC is output.


Result:
Result Proceed to
C128854 is not output A
C128854 is output B



A

END

B

11.PERFORM SYSTEM VARIANT LEARNING
a.

Perform system variant learning.

Chassis > Brake > Utility
Tester Display
Calibration
50005 435 4554
HINT:
·

System variant learning is automatically performed immediately after Test Mode is entered.

·

If learning has not yet been performed, the slip indicator light will remain on and DTC C128854 will be stored.

·

If system variant learning is not successful, the warning lights will not blink in the Test Mode pattern and DTC C128854 will not be cleared.




Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
12.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

b.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

Post-procedure1

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

13.RECONFIRM DTC
13.RECONFIRM DTC
a.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

b.

Check if the same DTC is output.


Result:
Result Proceed to
C128854 is not output A
C128854 is output B



A

END

B