Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF, TMMCZ Made) › from 2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0494155 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF, TMMCZ Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF, TMMCZ Made)  C141A00  ABS Time too Long  


DESCRIPTION

When the operating time of ABS control is detected to be excessive, the skid control ECU (brake actuator assembly) stores the following DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C141A00 ABS Time too Long Operating time of ABS control exceeds 18 seconds.
·

Front speed sensors

·

Speed sensor installation

·

Front speed sensor rotors (front axle hub sub-assemblies)

·

Rear speed sensors (rear axle hub and bearing assemblies)

·

Rear speed sensor rotors (rear axle hub and bearing assemblies)

·

Skid control ECU (brake actuator assembly)


Brake

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake actuator assembly), perform yaw rate and acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF, TMMCZ Made)>UTILITY


HINT:
·

The front speed sensor rotor is incorporated into the front axle hub sub-assembly.

If the front speed sensor rotor needs to be replaced, replace the front axle hub sub-assembly.

·

The rear speed sensor and rear speed sensor rotor are incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor and rear speed sensor rotor need to be replaced, replace the rear axle hub and bearing assembly.



PROCEDURE

1.CHECK PART NUMBER (BRAKE ACTUATOR ASSEMBLY)
a.

Check that the proper skid control ECU (brake actuator assembly) is installed.

OK:

Proper skid control ECU (brake actuator assembly) is installed.



Result:
Proceed to
OK
NG



OK

2.SYSTEM INFORMATION MEMORIZATION

NG

2.SYSTEM INFORMATION MEMORIZATION
a.

Perform system information memorization.

Chassis > Brake > Utility
Tester Display
Reset Memory
50005 435 4560
Chassis > Brake > Utility
Tester Display
Calibration
50005 435 4554
HINT:
·

If a new skid control ECU (brake actuator assembly) was installed, C121054 and C051D54 are output before "Calibration" is performed.

·

After performing "Reset Memory" using the GTS to clear the memorized value of the skid control ECU (brake actuator assembly), DTCs C121054 and C051D54 will be stored until system information memorization is performed.




Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

b.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

Post-procedure1

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

b.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

c.

Check if the same DTC is output.


Post-procedure1

d.

None


Result:
Result Proceed to
C141A00 is not output A
C141A00 is output B



A

END

B

5.PERFORM DEALER MODE (SIGNAL CHECK) INSPECTION (SPEED SENSOR CHECK)
5.PERFORM DEALER MODE (SIGNAL CHECK) INSPECTION (SPEED SENSOR CHECK)
a.

Using the GTS, perform a Dealer Mode (Signal Check) inspection sensor check and check that speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.

Chassis > Brake > Utility
Tester Display
Signal Check
50005 435 4558
OK:

Speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.


Result:
Result Proceed to
OK (for Front) A
OK (for Rear) B
NG C



NOTICE:
·

When cleaning the front speed sensor, make sure to clean the installation hole before installation.

·

Do not use parts cleaner when cleaning the front speed sensor rotor.




A

CLEAN OR REPLACE FRONT SPEED SENSOR AND FRONT SPEED SENSOR ROTOR

B

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

C

INSPECT AND REPAIR MALFUNCTIONING SPEED SENSOR CIRCUIT