| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| C060B00 | Left Electric Parking Brake Actuator Control | ·
Diagnosis Condition: - ·
Malfunction Status: When the ECU power supply is normal, a malfunction in the electric parking brake actuator LH internal circuit is detected. ·
Detection Time: - |
·
Parking brake actuator assembly LH ·
No. 2 parking brake wire assembly ·
Wire harness or connector ·
Skid control ECU (brake actuator assembly) |
DTC stored | An electric parking brake system malfunction is displayed on the multi-information display. |
| C060B11 | Left Electric Parking Brake Actuator Control Circuit Short to Ground | ·
Diagnosis Condition: Electric parking brake not operating ·
Malfunction Status: The ECU power supply is normal but there is a malfunction in the electric parking brake actuator LH internal circuit (short to GND). ·
Detection Time: Approximately 0.015 to 0.195 seconds (depending on each malfunction) |
·
Parking brake actuator assembly LH ·
No. 2 parking brake wire assembly ·
Wire harness or connector ·
Skid control ECU (brake actuator assembly) |
DTC stored | An electric parking brake system malfunction is displayed on the multi-information display. |
To ensure that the electric parking brake does not operate, wait for 3 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.
After replacing the skid control ECU (brake actuator assembly), perform calibration (brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration) after performing "Reset Memory".
When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light blinks (red) when the ignition switch is first turned ON.
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the oO1 and o2 No. 2 parking brake wire assembly connectors.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of No. 2 Parking Brake Wire Assembly | *b | (to wire harness connector) |
| *c | (to Parking Brake Actuator Assembly LH) | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| oO1-1 or o2-2 (MRL+) - Body ground and other terminals | Always | 10 kΩ or higher |
| oO1-2 or o2-1 (MRL-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Make sure the No. 2 parking brake wire assembly is securely installed.
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Disconnect the o2 parking brake actuator assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-13 (MRL+) or o2-2 (MRL+) - Body ground | Always | 10 kΩ or higher |
| A39-12 (MRL-) or o2-1 (MRL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model TMMF Made RHD)>REMOVAL
NG