This DTC is stored when the blind spot monitor sensor RH (A) detects a short to +B in the outer rear view mirror indicator RH.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AB512 | Outer Mirror Indicator (Module "A" Side) Circuit Short to Battery | Both of the following conditions are met:
·
The blind spot monitor system is on ·
The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time |
·
Outer mirror RH (outer rear view mirror indicator RH) ·
Outer rear view mirror assembly RH ·
Harness or connector ·
Blind spot monitor sensor RH (A) |
for TMC Made with 5 Door
for TMC Made with 3 Door
for TMMF, TMMCZ Made
When checking for DTCs, make sure that the blind spot monitor system is turned on.
Turn the ignition switch off.
Turn the ignition switch to ON.
Recheck for DTCs and check if the same DTC is output again.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Check the vehicle specifications.
| Result | Proceed to |
|---|---|
| for TMC Made with 5 Door | A |
| for TMC Made with 3 Door | B |
| for TMMF, TMMCZ Made | C |
A
B
C
Disconnect the S6 blind spot monitor sensor RH (A) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| S6-4 (OMIR) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A outer mirror RH (outer rear view mirror indicator RH) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| S6-4 (OMIR) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K8 outer rear view mirror assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| S6-4 (OMIR) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O37 blind spot monitor sensor RH (A) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| O37-4 (OMIR) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C outer mirror RH (outer rear view mirror indicator RH) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| O37-4 (OMIR) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K14 outer rear view mirror assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| O37-4 (OMIR) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O37 blind spot monitor sensor RH (A) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| O37-4 (OMIR) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C outer mirror RH (outer rear view mirror indicator RH) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| O37-4 (OMIR) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K14 outer rear view mirror assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| O37-4 (OMIR) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG