This DTC is stored when a telephone microphone assembly signal line is disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B157213 | Microphone Circuit Open | Current at terminal MCVD exceeds the malfunction threshold for 10 seconds or more while the ignition switch is ON | ·
Telephone transceiver assembly ·
Telephone microphone assembly ·
Harness or connector ·
Map light assembly |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System (for eCall).
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>REGISTRATION
Before replacing the telematics transceiver assembly, refer to Service Bulletin.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch to ON and wait for 10 seconds or more.
Check for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC B153711 or B153713 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Check the vehicle specification.
| Result | Proceed to |
|---|---|
| for TMMF Made and TMMCZ Made | A |
| for TMC Made | B |
A
B
Disconnect the H85 telephone transceiver assembly connector.
Disconnect the V6 map light assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H85-5 (MCVD) - V6-2 (MACC) | Always | Below 1 Ω |
| H85-6 (MCI+) - V6-3 (MCO+) | Always | Below 1 Ω |
| H85-7 (MCI-) - V6-4 (MCO-) | Always | Below 1 Ω |
| H85-5 (MCVD) or V6-2 (MACC) - Body ground | Always | 10 kΩ or higher |
| H85-6 (MCI+) or V6-3 (MCO+) - Body ground | Always | 10 kΩ or higher |
| H85-7 (MCI-) or V6-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| H85-23 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Telephone Transceiver Assembly) |
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H85-5 (MCVD) - Body ground | Ignition switch ON | 4 to 6 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Map Light Assembly) |
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Remove the telephone microphone assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V6-2 (MACC) - B-5 (MACC) | Always | Below 1 Ω |
| V6-3 (MCO+) - B-3 (MIC+) | Always | Below 1 Ω |
| V6-4 (MCO-) - B-2 (MIC-) | Always | Below 1 Ω |
| V6-2 (MACC) - V6-3 (MCO+) | Always | 10 kΩ or higher |
| V6-2 (MACC) - V6-4 (MCO-) | Always | 10 kΩ or higher |
| V6-3 (MCO+) - V6-4 (MCO-) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone microphone assembly with a new or known good one.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch to ON and wait for 10 seconds or more.
Check for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC B157213 is output | B |
A
B
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the telephone transceiver assembly with a new one.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the H85 telephone transceiver assembly connector.
Disconnect the V7 map light assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H85-5 (MCVD) - V7-16 (MACC) | Always | Below 1 Ω |
| H85-6 (MCI+) - V7-15 (MCO+) | Always | Below 1 Ω |
| H85-7 (MCI-) - V7-14 (MCO-) | Always | Below 1 Ω |
| H85-5 (MCVD) or V7-16 (MACC) - Body ground | Always | 10 kΩ or higher |
| H85-6 (MCI+) or V7-15 (MCO+) - Body ground | Always | 10 kΩ or higher |
| H85-7 (MCI-) or V7-14 (MCO-) - Body ground | Always | 10 kΩ or higher |
| H85-23 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Telephone Transceiver Assembly) |
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H85-5 (MCVD) - Body ground | Ignition switch ON | 4 to 6 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Map Light Assembly) |
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Remove the telephone microphone assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V7-16 (MACC) - B-5 (MACC) | Always | Below 1 Ω |
| V7-15 (MCO+) - B-3 (MCO+) | Always | Below 1 Ω |
| V7-14 (MCO-) - B-2 (MCO-) | Always | Below 1 Ω |
| V7-16 (MACC) - V7-15 (MCO+) | Always | 10 kΩ or higher |
| V7-16 (MACC) - V7-14 (MCO-) | Always | 10 kΩ or higher |
| V7-15 (MCO+) - V7-14 (MCO-) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone microphone assembly with a new or known good one.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch to ON and wait for 10 seconds or more.
Check for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC B157213 is output | B |
A
B
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the telephone transceiver assembly with a new one.
| Proceed to |
|---|
| NEXT |
NEXT