Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION
When replacing the telephone transceiver assembly, make sure to replace it with a new one.
Before replacing the telematics transceiver assembly, refer to Service Bulletin.
Inspect the fuses and relays related to this system before inspecting the suspected areas below.
Check the vehicle specification.
| Result | Proceed to |
|---|---|
| for TMMF Made and TMMCZ Made | A |
| for TMC Made | B |
A
B
Disconnect the H85 telephone transceiver assembly connector.
Disconnect the V6 map light assembly (manual (SOS) switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H85-3 (SIG-) - V6-16 (GND3) | Always | Below 1 Ω |
| H85-3 (SIG-) or V6-16 (GND3) - Body ground | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| V6-9 (RRID) - Body Ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Map Light Assembly (Manual (SOS) Switch)) |
Remove the map light assembly (manual (SOS) switch).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Apply auxiliary battery voltage to the connector.
| Measurement Condition | Condition | Specified Condition |
|---|---|---|
| Auxiliary battery positive (+) → V6-9 (RRID)
Auxiliary battery negative (-) → V6-16 (GND3) |
Always | Manual (SOS) switch illumination comes on |
Check if the manual (SOS) switch illumination comes on.
The manual (SOS) switch illumination comes on.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the H85 telephone transceiver assembly connector.
Disconnect the V7 map light assembly (manual (SOS) switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H85-3 (SIG-) - V7-5 (GND3) | Always | Below 1 Ω |
| H85-3 (SIG-) or V7-5 (GND3) - Body ground | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| V7-8 (RRID) - Body Ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Map Light Assembly (Manual (SOS) Switch)) |
Remove the map light assembly (manual (SOS) switch).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Apply auxiliary battery voltage to the connector.
| Measurement Condition | Condition | Specified Condition |
|---|---|---|
| Auxiliary battery positive (+) → V7-8 (RRID)
Auxiliary battery negative (-) → V7-5 (GND3) |
Always | Manual (SOS) switch illumination comes on |
Check if the manual (SOS) switch illumination comes on.
The manual (SOS) switch illumination comes on.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT