SYSTEM DESCRIPTION
Troubleshooting · Vehicles built from Aug 2005
| SYSTEM DESCRIPTION |
- HINT:
- The skid control ECU forms a single unit with the ABS and TRACTION actuator.
ABS (Anti-lock Brake System)
The ABS helps prevent the wheels from locking when the brakes are applied firmly or on a slippery surface.

Operation description
The skid control ECU detects wheel lock conditions by receiving vehicle speed signals from each speed sensor, and sends control signals to the pump motor and solenoid valve to prevent wheels from locking by controlling the brake fluid pressure of each wheel cylinder.
The ABS warning light comes on when the ABS system malfunctions.
EBD (Electronic Brake force Distribution)
The EBD control utilizes the ABS, realizing the proper brake force distribution between the front and rear wheels in accordance with the driving conditions and vehicle load. In addition, when the brakes are applied while cornering, it also controls the braking forces of the right and left wheels, helping to maintain vehicle stability.

Operation description
The skid control ECU receives speed signals from each speed sensor to detect the slip conditions of the wheels and sends control signals to the solenoid.
The solenoid valve controls the brake fluid pressure of each wheel cylinder and divides the control power properly between the front and rear wheels and the right and left wheels.
The BRAKE warning light comes on to indicate malfunctions in the EBD system.
BA (Brake Assist)
The primary purpose of the brake assist system is to provide auxiliary brake force to assist drivers who cannot generate a large enough brake force during emergency braking, thus helping to maximize the vehicle's braking performance.

Operation description
The skid control ECU receives speed signals from each speed sensor and the fluid pressure signal from the master cylinder pressure sensor to determine whether brake assist is necessary. If brake assist is deemed necessary, the skid control ECU sends control signals to the pump motor and solenoid. The pump and the solenoid valve then control the pressure applied to each wheel cylinder. The ABS warning light comes on to indicate malfunctions in the BA (brake assist) system.
TRC (Traction Control)
The TRC system helps prevent the drive wheels from slipping if the driver presses down on the accelerator pedal excessively when starting off or accelerating on a slippery surface.

Operation description
The skid control ECU detects the vehicle's slip condition by receiving signals from each speed sensor and the ECM via CAN communication. The skid control ECU controls engine torque with the ECM via CAN communication and brake fluid pressure through the pump and solenoid valve. The SLIP indicator light blinks when the system is operating. The VSC warning light and SLIP indicator light come on when the TRC system malfunctions.
VSC (Vehicle Stability Control)
The VSC system helps prevent the vehicle from slipping sideways when front or rear wheel skidding occurs while cornering.

Operation description
The skid control ECU determines the vehicle condition by receiving signals from the speed sensor, the yaw rate and deceleration sensor and the steering sensor. The skid control ECU controls engine torque with the ECM via CAN communication and brake fluid pressure through the pump and solenoid valve. The SLIP indicator light blinks and the skid control buzzer sounds when the system is operating. The VSC warning light and SLIP indicator light come on when the VSC system malfunctions.
| ABS with EBD, BA, TRC and VSC OPERATION |
The skid control ECU calculates vehicle stability tendency based on the signals from the 4 wheel speed sensors, the yaw rate and deceleration sensor and the steering sensor. In addition, it evaluates the results of the calculations to determine whether any control actions (control of the engine output torque by electronic throttle control and of the brake fluid pressure by the ABS and TRACTION actuator) should be implemented.
The SLIP indicator blinks and the skid control buzzer sounds to inform the drive that the VSC system is operating. The SLIP indicator also blinks when traction control is operating, and the operation being performed is displayed.
| FAIL SAFE FUNCTION |
When a failure occurs in the ABS with BA, TRC and VSC systems, the ABS and VSC warning lights, and SLIP indicator light come on, and the operation of those systems is prohibited. In addition to this, when a failure which disables the EBD operation occurs, the brake warning light comes on and its operation is prohibited.
If control is prohibited due to a malfunction during operation, control is disabled gradually to avoid sudden vehicle instability.
| INITIAL CHECK |
When the vehicle speed first reaches approximately 6 km/h (4 mph) or more after the ignition switch is turned on (IG), each solenoid valve and the motor of the ABS and TRACTION actuator are sequentially activated to perform electrical checks. During the initial check, the operating sound of the solenoid valve and motor can be heard from the engine compartment, but this does not indicate a malfunction.
| SERVICE MODE |
VSC operation can be disabled by operating the intelligent tester.
- HINT:
- Refer to the intelligent tester operator's manual for further details.
| FUNCTION OF COMPONENTS |
| Components |
Functions |
| Front speed sensor (Semiconductor speed sensor, magnetic sensor rotor) |
|
| Skid control sensor (Semiconductor speed sensor, magnetic sensor rotor) |
|
| Skid control ECU (Housed in ABS and TRACTION actuator) |
|
| ABS and TRACTION actuator |
|
| Solenoid relay |
|
| Motor relay (VSC1 relay) |
|
| Fail-safe relay (VSC2 relay) |
|
| Steering sensor |
|
| Yaw rate and deceleration sensor |
|
| Master cylinder pressure sensor |
|
| ECM |
|
| ABS warning light |
|
| VSC warning light |
|
| BRAKE warning light |
|
| SLIP indicator light |
|
| Skid control buzzer |
|