2005-2008 Yaris · Service Manual BRAKE

SYSTEM DESCRIPTION

Troubleshooting · Vehicles built from Nov 2005


SYSTEM DESCRIPTION

HINT:
The skid control ECU forms a single unit with the ABS and TRACTION actuator.

  1. ABS (Anti-lock Brake System)
    The ABS helps prevent the wheels from locking when the brakes are applied firmly or on a slippery surface.
    C115099E03

    1. Operation description
      The skid control ECU detects wheel lock conditions by receiving vehicle speed signals from each speed sensor, and sends control signals to the pump motor and solenoid valve to prevent the wheels from locking by controlling the brake fluid pressure of each wheel cylinder.
      The ABS warning light comes on when the ABS system malfunctions.

  2. EBD (Electronic Brake force Distribution)
    The EBD control utilizes the ABS, realizing the proper brake force distribution between the front and rear wheels in accordance with the driving conditions and vehicle load. In addition, when the brakes are applied while cornering, it also controls the braking forces of the right and left wheels, helping to maintain vehicle stability.
    C115100E03

    1. Operation description
      The skid control ECU receives speed signals from each speed sensor to detect the slip conditions of the wheels and sends control signals to the solenoid.
      The solenoid valve controls the brake fluid pressure of each wheel cylinder and divides the control power properly between the front and rear wheels and the right and left wheels.
      The BRAKE warning light comes on to indicate malfunctions in the EBD system.

  3. BA (Brake Assist)
    The primary purpose of the brake assist system is to provide auxiliary brake force to assist drivers who cannot generate a large enough brake force during emergency braking, thus helping to maximize the vehicle's braking performance.
    C115101E01

    1. Operation description
      The skid control ECU receives speed signals from each speed sensor and the fluid pressure signal from the master cylinder pressure sensor to determine whether brake assist is necessary. If brake assist is deemed necessary, the skid control ECU sends control signals to the pump motor and solenoid. The pump and the solenoid valve then control the pressure applied to each wheel cylinder. The ABS warning light comes on to indicate malfunctions in the BA (brake assist) system.

  4. TRC (Traction Control)
    The TRC system helps prevent the drive wheels from slipping if the driver presses down on the accelerator pedal excessively when starting off or accelerating on a slippery surface.
    C129360E01

    1. Operation description
      The skid control ECU detects the vehicle's slip condition by receiving signals from each speed sensor and the ECM via CAN communication. The skid control ECU controls engine torque with the ECM via CAN communication and brake fluid pressure through the pump and solenoid valve. The SLIP indicator light blinks when the system is operating. The VSC warning light and SLIP indicator light come on when the TRC system malfunctions.

  5. VSC (Vehicle Stability Control)
    The VSC system helps prevent the vehicle from slipping sideways when front or rear wheel skidding occurs while cornering.
    C129361E01

    1. Operation description
      The skid control ECU determines the vehicle condition by receiving signals from the speed sensor, the yaw rate and deceleration sensor and the steering angle sensor. The skid control ECU controls engine torque with the ECM via CAN communication and brake fluid pressure through the pump and solenoid valve. The SLIP indicator light blinks and the skid control buzzer sounds when the system is operating. The VSC warning light and SLIP indicator light come on when the VSC system malfunctions.


ABS with EBD, BA, TRC and VSC OPERATION
  1. The skid control ECU calculates vehicle stability tendency based on the signals from the 4 wheel speed sensors, the yaw rate and deceleration sensor and the steering angle sensor. In addition, it evaluates the results of the calculations to determine whether any control actions (control of the engine output torque by electronic throttle control and of the brake fluid pressure by the ABS and TRACTION actuator) should be implemented.

  2. The SLIP indicator blinks and the skid control buzzer sounds to inform the driver that the VSC system is operating. The SLIP indicator also blinks when traction control is operating, and the operation being performed is displayed.


FAIL SAFE FUNCTION
  1. When a failure occurs in the ABS with BA, TRC and VSC systems, the ABS and VSC warning lights, and SLIP indicator light come on, and the operation of those systems is prohibited. In addition to this, when a failure which disables the EBD operation occurs, the brake warning light comes on and its operation is prohibited.

  2. If control is prohibited due to a malfunction during operation, control is disabled gradually to avoid sudden vehicle instability.


INITIAL CHECK
  1. When the vehicle speed first reaches approximately 20 km/h (12 mph) or more after the ignition switch is turned on (IG), each solenoid valve and the motor of the ABS and TRACTION actuator are sequentially activated to perform electrical checks. During the initial check, the operating sound of the motor can be heard from the engine compartment, but this does not indicate a malfunction.


FUNCTION OF COMPONENTS
Components
Functions
Front speed sensor
(Semiconductor speed sensor, magnetic sensor rotor)
  1. Detects the wheel speed and sends a signal to the skid control ECU.
  2. The front speed sensor (semiconductor speed sensor) with the integrated bearing and the sensor rotor (magnetic sensor rotor) are installed on the front axle hub.
  3. The magnetic sensor rotor is equipped with north and south poles (48 poles each), which are evenly spaced around its circumference.
  4. The magnetic field changes as the magnetic sensor rotor rotates. The semiconductor speed sensor detects the change and outputs it as the vehicle speed pulse.
Skid control sensor
(Semiconductor speed sensor, magnetic sensor rotor)
  1. The skid control sensor (semiconductor speed sensor) and the sensor rotor (magnetic sensor rotor) are installed on the rear axle carrier.
  2. The skid control sensor has the same structure and functions as the front speed sensor.
Skid control ECU
(Housed in ABS and TRACTION actuator)
  1. Processes the signals from each sensor to control the ABS, BA, TRC, and VSC.
  2. Sends and receives control signals to and from the ECM, yaw rate and deceleration sensor, steering angle sensor, etc. via CAN communication.
ABS and TRACTION actuator
  1. Consists of the master cylinder cut solenoid valve, holding solenoid valve, pressure reduction solenoid valve, pump motor, and reservoir, and adjusts the brake fluid pressure applied to each wheel cylinder.
  2. Houses the skid control ECU.
Solenoid relay
  1. Supplies power to each solenoid.
  2. Housed in the skid control ECU.
Steering angle sensor
  1. Detects the steering extent and direction and sends signals to the skid control ECU via CAN communication.
  2. Has a magnetic resistance element which detects the rotation of the magnet housed in the detection gear in order to detect the changes in magnetic resistance and the steering amount and direction.
Yaw rate and deceleration sensor
  1. Yaw rate sensor detects the vehicle's angular velocity (yaw rate) in the vertical direction based on the extent and direction of the quartz tuning fork due to the Coriolis force.
  2. Deceleration sensor measures the capacity of the condenser that changes with the distance between the electrodes depending on G force, which occurs when the vehicle is accelerated, and converts the measured value into electrical signals.
  3. Sends signals to the skid control ECU via CAN communication.
Master cylinder pressure sensor
  1. Detects the brake fluid pressure in the master cylinder.
  2. Housed in the ABS and TRACTION actuator.
ECM
  1. Controls the engine output when TRC and VSC are operating with the skid control ECU via CAN communication.
ABS warning light
  1. Illuminates to inform the driver that a malfunction in the ABS has occurred.
  2. Blinks to indicate DTCs that relate to the ABS.
VSC warning light
  1. Illuminates to inform the driver that a malfunction in the VSC system has occurred.
  2. Blinks to indicate DTCs that relate to the VSC.
BRAKE warning light
  1. Illuminates to inform the driver that the parking brake is ON when the system is normal, and when the brake fluid has decreased.
  2. Illuminates to inform the driver that a malfunction in the EBD has occurred.
SLIP indicator light
  1. Blinks to inform the driver that TRC and VSC are operating.
  2. Illuminates to inform the driver that a malfunction has occurred in the TRC or VSC system.
Skid control buzzer
  1. Intermittently sounds to inform the driver that the VSC is operating.
  2. Housed in the combination meter.
← SYSTEM DIAGRAM (from Nov 2005)HOW TO PROCEED WITH TROUBLESHOOTING (from Nov 2005) →