DISPOSAL
Removal / installation · Vehicles built from Nov 2005
- HINT:
- When scrapping a vehicle equipped with the SRS or disposing of a steering pad, deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the SERVICE DEPT. of the DISTRIBUTOR.
- CAUTION:
- Never dispose of a steering pad that has an undeployed airbag.
- The airbag emits an exploding sound when it is deployed, so perform the operation outdoors, and where it will not create a nuisance to nearby residents.
-
When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.

- When deploying the airbag, perform the operation at least 10 m (33 ft) away from the steering pad.
- The steering pad becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
- Use gloves and safety glasses when handling a steering pad with a deployed airbag.
- Do not apply water, etc. to a steering pad with a deployed airbag.
- Always wash your hands with water after completing the operation.
- Never dispose of a steering pad that has an undeployed airbag.
| 1. DISPOSE OF STEERING PAD (WHEN INSTALLED IN VEHICLE) |
- HINT:
- Prepare a battery as the power source to deploy the airbag.
Check the function of SST.

- SST
- 09082-00700
- CAUTION:
- Always use the specified SST (SRS Airbag Deployment Tool) when deploying the airbag.
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.

Press the SST activation switch, and check that the LED of the SST activation switch illuminates.

- CAUTION:
- Do not connect the SST connector (yellow colored one) to the airbag.
- If the LED illuminates when the activation switch is not being pressed, SST may be malfunctioning. Do not use SST.
- Do not connect the SST connector (yellow colored one) to the airbag.
Disconnect SST from the battery.
Disconnect the cable from the negative battery terminal.
Remove the steering column cover.

Turn the steering wheel 90 degrees in both directions and remove the 2 screws.
Remove the screw from the lower portion of the steering cover lower.
Disengage the 2 claws and remove the steering column cover lower.
Connect SST.

- CAUTION:
- Check that there is no slack in the steering wheel and steering pad.
Disconnect the airbag connector, as shown in the illustration.
- NOTICE:
- Do not damage the airbag wire harness when handling the airbag connector.
Connect SST.

- SST
- 09082-00700
09082-00780
- NOTICE:
- Do not lock the secondary lock of the twin lock to avoid damaging the SST connector and wire harness.
Move SST to at least 10 m (33 ft) away from the vehicle front side window.

Maintaining enough clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.
- NOTICE:
- Do not damage the SST wire harness.
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.
Deploy the airbag.
Check that no one is inside the vehicle or within a 10 m (33 ft) radius of the vehicle.
Press the SST activation switch and deploy the airbag.
- CAUTION:
- Make sure that no one is near the vehicle when deploying the airbag.
- The steering pad becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
- Use gloves and safety glasses when handling a steering pad with a deployed airbag.
- Always wash your hands with water after completing the operation.
- Do not apply water, etc. to a steering pad with a deployed airbag.
- Make sure that no one is near the vehicle when deploying the airbag.
- HINT:
- The airbag is deployed as the LED of the SST activation switch illuminates.
