2005-2008 Yaris · Service Manual ENGINE

P0132 Oxygen Sensor Circuit High Voltage Bank1 Sensor1

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

In order to obtain a high purification rate for the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a Three-Way Catalytic Converter (TWC) is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric air-fuel ratio. The heated oxygen sensor has the characteristic whereby its output voltage changes suddenly in the vicinity of the stoichiometric air-fuel ratio. This is used to detect the oxygen concentration in the exhaust gas and provide the ECM with feedback to control the air-fuel ratio. When the air-fuel ratio becomes lean, the oxygen concentration in the exhaust gas increases. The heated oxygen sensor informs the ECM of the lean condition (low voltage, i.e. less than 0.45 V). When the air-fuel ratio is richer than the stoichiometric air-fuel level, the oxygen concentration in the exhaust gas is reduced. And the heated oxygen sensor informs the ECM of the rich condition (high voltage, i.e. more than 0.45 V). The ECM judges, using the voltage output of the heated oxygen sensor, whether the air-fuel ratio is rich or lean and controls the injection time accordingly. If a malfunction of the heated oxygen sensor causes an output of abnormal voltage, the ECM is unable to perform accurate air-fuel ratio control. The heated oxygen sensor includes a heater which heats the zirconia element. The heater is controlled by the ECM. When the intake air volume is low (the temperature of the exhaust gas is low), a current flows to the heater in order to heat the sensor for accurate oxygen concentration detection.
G035432E07
DTC No.
DTC Detection Condition
Trouble Area
P0132
Heated oxygen sensor (sensor 1) output voltage is 1.5 V or more for 5 second or more (3 trip detection logic).
  1. Short in signal output circuit and power source circuit of heated oxygen sensor (sensor 1)
  2. Heated oxygen sensor (sensor 1)
  3. ECM

HINT:
Sensor 1 refers to the sensor near the engine assembly.


WIRING DIAGRAM

A109127E01

CONFIRMATION DRIVING PATTERN

CAUTION:
Strictly observe traffic laws when performing the confirmation driving pattern.

DTC P0132 is detected when the vehicle is driven with a city driving pattern at an average vehicle speed of approximately 50 km/h (31 mph) for approximately 30 minutes.

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)
A120336E01
  1. Disconnect the heated oxygen sensor (sensor 1) connector.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    OX1A (C36-3) or OX1A (C33-18) - HT1A (C36-1) or HT1A (C33-41)
    10 kΩ or higher
    OX1A (C36-3) - +B (C36-2)
    10 kΩ or higher

  1. Reconnect the heated oxygen sensor (sensor 1) connector.

  1. Reconnect the ECM connector.A116151E01



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HEATED OXYGEN SENSOR (SENSOR 1)


← P0130 Oxygen (A/F) Sensor Circuit (Bank 1 Sensor 1) (+ P0134) (from Aug 2005)P0133 Oxygen (A/F) Sensor Circuit Slow Response (Bank 1 Sensor 1) (from Aug 2005) →