2005-2008 Yaris · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL FRONT DISC BRAKE BUSH DUST BOOT

C129740E01
  1. Apply lithium soap base glycol grease to 2 new dust boots.

  1. C127216
    Install the 2 dust boots onto the disc brake cylinder.


2. INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY

C129741E01
  1. Apply lithium soap base glycol grease to the slide pins.

  1. Using "Torx" socket wrench T45, temporarily install the disc brake cylinder with the 2 slide pins.

    Torque:
    28 N*m{ 280 kgf*cm , 20 ft.*lbf }

  1. Install the 2 slide pin caps.


3. INSTALL FRONT DISC BRAKE PAD

C129742
  1. Install the brake pad onto the disc brake cylinder mounting.

    NOTICE:
    There should be no oil or grease on the friction surfaces of the disc brake pads.


4. INSTALL FRONT DISC BRAKE ANTI-RATTLE SPRING

C129743E01
  1. Push end A of the spring into the groove of the disc brake cylinder and install spring sliding arm A' onto the disc brake cylinder mounting anchor.

  1. C129744E01
    Push the spring in the direction of the arrow to flex it until end B can be inserted into the groove of the disc brake cylinder.

  1. C129745E01
    While pushing end B of the spring into the groove of the disc brake cylinder, flex spring sliding arm B' and install arm B' onto the disc brake cylinder mounting anchor.

  1. C127214
    Make sure that the spring is securely installed.


5. INSTALL FRONT DISC

C108932E01
  1. Align the matchmarks of the disc and axle hub and install the disc.

    NOTICE:
    When replacing the disc, select the position that gives the minimum disc runout.


6. INSTALL FRONT DISC BRAKE CYLINDER MOUNTING

C127213
  1. Install the disc brake cylinder mounting onto the steering knuckle with the 2 bolts.

    Torque:
    107 N*m{ 1,089 kgf*cm , 79 ft.*lbf }


7. INSTALL FRONT FLEXIBLE HOSE

C127210
  1. Connect the flexible hose with the union bolt and a new gasket.

    Torque:
    30 N*m{ 310 kgf*cm , 22 ft.*lbf }

    HINT:
    Install the flexible hose lock securely into the lock hole in the disc brake cylinder.


8. FILL RESERVOIR WITH BRAKE FLUID

C137247E01
  1. Remove the cowl top ventilator louver.

  1. C130290E01
    Set the brake fluid can upside down on the reservoir.

    Fluid:
    SAE J1704 or FMVSS No. 116 DOT4


9. BLEED MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.

  1. C130291E01
    w/o VSC:

    1. Using SST, disconnect the brake tubes from the master cylinder.

      SST
      09023-00100  

  1. w/ VSC:

    1. Using SST, disconnect the brake tubes from the master cylinder.

      SST
      09023-38200  

  1. C130292E01
    Slowly depress the brake pedal and hold it there (Step A).

  1. C130293E01
    Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat steps A and B 3 or 4 times.

  1. C130291E01
    w/o VSC:

    1. Using SST, connect the brake tubes to the master cylinder.

      SST
      09023-00100  

      Torque:
      for use without SST:
      15 N*m{ 155 kgf*cm , 11 ft.*lbf }
      for use with SST:
      14 N*m{ 143 kgf*cm , 10 ft.*lbf }

      HINT:
      1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
      2. This torque value is effective when SST is parallel to a torque wrench.

  1. w/ VSC:

    1. Using SST, connect the brake tubes to the master cylinder.

      SST
      09023-38200  

      Torque:
      for use without SST:
      20 N*m{ 199 kgf*cm , 14 ft.*lbf }
      for use with SST:
      18 N*m{ 180 kgf*cm , 13 ft.*lbf }

      HINT:
      1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
      2. This torque value is effective when SST is parallel to a torque wrench.


10. BLEED BRAKE LINE

C130294
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).

  1. Repeat steps C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    Front Disc Brake:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }
    Rear Drum Brake:
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
    Rear Disc Brake:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.


11. BLEED BRAKE ACTUATOR (w/ VSC)

NOTICE:
After bleeding the air from the brake system, if the height or feel of the brake pedal cannot be obtained, perform air bleeding of the brake actuator with an intelligent tester by following the procedure below.

  1. Depress the brake pedal more than 20 times with the engine off.

  1. A107926E08
    Connect the intelligent tester to the DLC3, and turn the ignition switch on (IG).

    NOTICE:
    Do not start the engine.

  1. Select AIR BLEEDING on the intelligent tester.

    HINT:
    Refer to the intelligent tester operator's manual for further details.

  1. Bleed the air out of the brake line when Step 1: Increase appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty of brake fluid.


    1. Connect the vinyl tube to either one of the bleeder plugs.

    2. C130294
      Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step E).

    3. When fluid stops coming out, tighten the bleeder plug and release the brake pedal (Step F).

    4. Repeat steps E and F until all air in the fluid is completely bled out.

    5. Tighten the bleeder plug completely.

      Torque:
      Front Disc Brake:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }
      Rear Drum Brake:
      9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
      Rear Disc Brake:
      14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    6. Repeat the above procedure for each wheel to bleed the air out of the brake line.

  1. Bleed the air out of the suction line when Step 2: Inhalation appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty of brake fluid.


    1. Connect the vinyl tube to the bleeder plug at the right front wheel or the right rear wheel and loosen the bleeder plug.

    2. Operate the brake actuator to bleed the air using the intelligent tester (Step G).

      NOTICE:
      Release the brake pedal at this time.

      HINT:
      This operation stops automatically after 4 seconds.

    3. Check if the operation has stopped by referring to the intelligent tester display (Step H).

    4. Repeat steps G and H until all air in the fluid is completely bled out.

    5. Tighten the bleeder plug.

      Torque:
      Front Disc Brake:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }
      Rear Drum Brake:
      9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
      Rear Disc Brake:
      14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    6. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

  1. Bleed the air out of the pressure reduction line when Step 3: Decrease appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty of brake fluid.


    1. Connect the vinyl tube to either one of the bleeder plugs.

    2. Loosen the bleeder plug (Step I).

    3. Using the intelligent tester, operate the brake actuator assembly, completely depress the brake pedal and hold it there.

      NOTICE:
      1. During this procedure, the pedal will feel heavy, but completely depress it so that the brake fluid comes out of the bleeder plug.
      2. Hold the brake pedal depressed. Do not depress and release the pedal repeatedly.

      HINT:
      1. The operation stops automatically after 4 seconds. When performing this procedure continuously, set an interval of at least 20 seconds.
      2. When the operation is complete, the brake pedal goes down slightly. This is a normal phenomenon caused when the solenoid opens.

    4. Tighten the bleeder plug, then release the brake pedal (Step J).

    5. Repeat steps I and J until all the air in the fluid is completely bled out.

    6. Tighten the bleeder plug.

      Torque:
      Front Disc Brake:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }
      Rear Drum Brake:
      9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
      Rear Disc Brake:
      14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    7. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

  1. Bleed the air out of the brake line again when Step 4: Increase appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty of brake fluid.


    1. Connect the vinyl tube to either one of the bleeder plugs.

    2. C130294
      Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step K).

    3. When fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step L).

    4. Repeat steps K and L until all the air in the fluid is completely bled out.

    5. Tighten the bleeder plug.

      Torque:
      Front Disc Brake:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }
      Rear Drum Brake:
      9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
      Rear Disc Brake:
      14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    6. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

    7. Make sure that the air bleeding is complete by referring to the intelligent tester display.


12. CHECK FLUID LEVEL IN RESERVOIR
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1704 or FMVSS No. 116 DOT4


13. CHECK FOR BRAKE FLUID LEAKAGE

14. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }

← REASSEMBLY (from Nov 2005)COMPONENTS (from Jan 2006) →