2005-2008 Yaris · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Jan 2006


1. INSTALL FRONT DISC

C108932E01
  1. Align the matchmarks of the disc and axle hub and install the disc.

    NOTICE:
    When replacing the disc, select the position that gives the minimum disc runout.


2. INSTALL FRONT DISC BRAKE CYLINDER MOUNTING

C108931
  1. Install the disc brake cylinder mounting onto the steering knuckle with the 2 bolts.

    Torque:
    107 N*m{ 1,089 kgf*cm , 79 ft.*lbf }


3. INSTALL NO. 1 BUSH DUST BOOT

C116963E01
  1. Apply lithium soap base glycol grease to 2 new dust boots.

  1. Install the 2 dust boots onto the disc brake cylinder mounting.


4. INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSH

C116962E01
  1. Apply lithium soap base glycol grease to the slide pins and a new slide bush, as shown in the illustration.

  1. Install the slide bush onto the slide pin (lower).


5. INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN

C116961E01
  1. Install the slide pin (upper) and slide pin (lower) onto the cylinder mounting.


6. INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE

C121849
  1. Install the 4 disc brake pad support plates onto the disc brake cylinder mounting.


7. INSTALL PAD WEAR INDICATOR NO. 1 PLATE
  1. Install the indicator plates onto the upper side of the brake pad.


8. INSTALL FRONT ANTI SQUEAL SHIM KIT

C116960E01
  1. Apply disc brake grease to both sides of each No. 1 anti-squeal shim.

  1. Install the anti squeal shims onto each brake pad.


9. INSTALL FRONT DISC BRAKE PAD KIT (PAD ONLY)

C107601
  1. Install the 2 disc brake pads onto the disc brake cylinder mounting.

    NOTICE:
    There should be no oil or grease on the friction surfaces of the disc brake pads or the front disc.


10. INSTALL DISC BRAKE CYLINDER ASSEMBLY

C107600
  1. Install the disc brake cylinder onto the disc brake cylinder mounting with the 2 bolts.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }


11. CONNECT FRONT FLEXIBLE HOSE

C107599
  1. Connect the flexible hose with the union bolt and a new gasket.

    Torque:
    30 N*m{ 310 kgf*cm , 22 ft.*lbf }

    HINT:
    Install the flexible hose lock securely into the lock hole in the disc brake cylinder.


12. FILL RESERVOIR WITH BRAKE FLUID

C133125E01
  1. Remove the cowl top No. 2 ventilator louver center.

  1. C133126E01
    Set the brake fluid can upside down on the reservoir.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3
    SAE J1704 or FMVSS No. 116 DOT4


13. BLEED MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.

  1. C116910E01
    Using SST, disconnect the brake tubes from the master cylinder.
    SST
    09023-00100  

  1. C116911E01
    Slowly depress the brake pedal and hold it there (Step A).

  1. C116912E01
    Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat steps A and B 3 or 4 times.

  1. C116910E01
    Using SST, connect the brake tubes to the master cylinder.
    SST
    09023-00100  

    Torque:
    for use without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    for use with SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.


14. BLEED BRAKE LINE

C116913
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).

  1. Repeat steps C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.


15. CHECK FLUID LEVEL IN RESERVOIR
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3
    SAE J1704 or FMVSS No. 116 DOT4


16. CHECK FOR BRAKE FLUID LEAKAGE

17. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }

← REASSEMBLY (from Jan 2006)COMPONENTS (from Aug 2005) →