P2102 Throttle Actuator Control Motor Circuit Low
Diagnostic trouble codes · Vehicles built from Nov 2006
Also covers:
- P2103 Throttle Actuator Control Motor Circuit High
DESCRIPTION
The throttle actuator built into the throttle body assembly is operated by the ECM and opens and closes the throttle valve using gears.The opening angle of the throttle valve is detected by the Throttle Position (TP) sensor, which is mounted on the throttle body assembly. The TP sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.
- HINT:
- This ETCS (Electronic Throttle Control System) does not use a throttle cable.
DTC No.
DTC Detection Condition
Trouble Area
P2102
Following conditions (a) and (b) met for 2.0 seconds (1 trip detection logic):
(a) Throttle actuator duty ratio 80% or more
(b) Throttle actuator current less than 0.5 A
- Open in throttle actuator circuit
- Throttle body assembly
- ECM
P2103
Either of following conditions met (1 trip detection logic): - Hybrid IC diagnosis signal fail
- Hybrid IC current limiter port fail
- Short in throttle actuator circuit
- Throttle body assembly
- ECM
- Open in throttle actuator circuit
FAIL-SAFE
When either of these DTCs, or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions, are set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator off, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed gently, the vehicle can be driven slowly. Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using an intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- Read freeze frame data using an intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- The throttle actuator current (Throttle Motor Current) and the throttle actuator duty ratio (Throttle Motor Open Duty / Throttle Motor Close Duty) can be read using the intelligent tester. However, the ECM shuts off the throttle actuator current when the ETCS malfunctions.
- The throttle actuator current (Throttle Motor Current) and the throttle actuator duty ratio (Throttle Motor Open Duty / Throttle Motor Close Duty) can be read using the intelligent tester. However, the ECM shuts off the throttle actuator current when the ETCS malfunctions.
| 1. INSPECT THROTTLE BODY ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR) |
Disconnect the throttle body connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
2 (M+) - 1 (M-)
20°C (68°F)
0.3 to 100 Ω
Reconnect the throttle body connector.
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (THROTTLE BODY - ECM) |
Disconnect the throttle body connector.

Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance (Check for open):
Tester Connection
Condition
Specified Condition
C17-2 (M+) - C20-42 (M+)
Always
Below 1 Ω
C17-1 (M-) - C20-41 (M-)
Always
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Condition
Specified Condition
C17-2 (M+) or C20-42 (M+) - Body ground
Always
10 kΩ or higher
C17-1 (M-) or C20-41 (M-) - Body ground
Always
10 kΩ or higher
Reconnect the throttle body connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 3. REPLACE THROTTLE BODY ASSEMBLY |
| NEXT | |
| 4. CHECK WHETHER DTC OUTPUT RECURS (DTC P2102 OR P2103) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC / Clear.
Clear DTCs.
Start the engine.
Drive the vehicle for several minutes.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
- Result:
Result
Proceed to
P2102 or P2103
A
No output
B
|
|
||||
| A | ||
| ||
