2005-2008 Yaris · Service Manual ENGINE

P0724 Brake Switch "B" Circuit High

Diagnostic trouble codes · Vehicles built from Nov 2006

DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in the lock-up condition when the brakes are suddenly applied.
When the brake pedal is depressed, this switch sends a signal to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.
DTC No.
DTC Detection Condition
Trouble Area
P0724
Stop light switch remains ON even when vehicle is driven in GO (30 km/h (18.63 mph) or more) and STOP (less than 3 km/h (1.86 mph)) pattern 5 times (2 trip detection logic)
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. ECM

WIRING DIAGRAM

Refer to DTC P0504 (Click here).

INSPECTION PROCEDURE

HINT:
  1. The following procedure is based on the premise that the stop lights are functioning normally. If the stop lights are not functioning, proceed to Stop Light Circuit (Click here).
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Stop Light Switch.

  1. Read the value displayed on the tester when the depressed and released brake pedal.

    Standard:
    Brake Pedal
    Display
    Released
    OFF
    Depressed
    ON



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT STOP LIGHT SWITCH

  1. A115657E12
    Remove the stop light switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Position
    Specified Condition
    1 - 2
    Switch pin not pushed
    Below 1 Ω
    Switch pin pushed
    10 kΩ or higher
    3 - 4
    Switch pin not pushed
    10 kΩ or higher
    Switch pin pushed
    Below 1 Ω

  1. Reinstall the stop light switch.



NG
REPLACE STOP LIGHT SWITCH
OK


3. CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH)

  1. A159455E01
    Disconnect the stop light switch connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (check for open):
    Tester Connection
    Condition
    Specified Condition
    A21-36 (STP) - A13-1
    Always
    Below 1 Ω
    A21-35 (ST-) - A13-4
    Always
    Below 1 Ω

    Standard resistance (check for short):
    Tester Connection
    Condition
    Specified Condition
    A21-36 (STP) or A13-1 - Body ground
    Always
    10 kΩ or higher
    A21-35 (ST-) or A13-4 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the stop light switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0617 Starter Relay Circuit High (from Nov 2006)P2102 Throttle Actuator Control Motor Circuit Low (+ P2103) (from Nov 2006) →