2005-2008 Yaris · Service Manual ENGINE

P2118 Throttle Actuator Control Motor Current Range / Performance

Diagnostic trouble codes · Vehicles built from Nov 2006

DESCRIPTION

The ETCS (Electronic Throttle Control System) has a dedicated power supply circuit. The voltage (+BM) is monitored and when it is low (less than 4 V), the ECM determines that there is a malfunction in the ETCS and cuts off the current to the throttle actuator.
When the voltage becomes unstable, the ETCS itself becomes unstable. For this reason, when the voltage is low, the current to the throttle actuator is cut. If repairs are made and the system returns to normal, turn the ignition switch off. The ECM then allows the current to flow to the throttle actuator so that it can be restarted.

HINT:
The ETCS does not use a throttle cable.

A112629E12
DTC No.
DTC Detection Condition
Trouble Area
P2118
Open in ETCS (Electronic Throttle Control System) power source (+BM) circuit
(1 trip detection logic)
  1. Open in ETCS power source circuit
  2. Battery
  3. Battery terminals
  1. ETCS fuse
  1. ECM

FAIL-SAFE

When this DTC, or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions, are set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator off, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed gently, the vehicle can be driven slowly. Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A159166E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (+BM VOLTAGE)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / +BM voltage.

  1. Read the value displayed on the tester.

    Standard voltage:
    11 to 14 V

    Result:
    Result
    Proceed to
    Outside standard range
    A
    Within standard range
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2. INSPECT FUSE (ETCS FUSE)

  1. A112591E02
    Remove the ETCS fuse from the engine room R/B and J/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    ETCS fuse
    Always
    Below 1 Ω

  1. Reinstall the ETCS fuse.



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


3. CHECK HARNESS AND CONNECTOR (+BM CIRCUIT)

  1. A106902E26
    Disconnect the ECM connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A21-3 (+BM) - C20-104 (E1)
    Always
    11 to 14 V

  1. Reconnect the ECM connectors.



NG
Go to step 4
OK

REPLACE ECM

4. CHECK HARNESS AND CONNECTOR (ECM - ETCS FUSE)

  1. A159456E01
    Disconnect the ECM connector.

  1. Remove the ETCS fuse from the engine room R/B and J/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (check for open):
    Tester Connection
    Condition
    Specified Condition
    2 (ETCS fuse) - A21-3 (+BM)
    Always
    Below 1 Ω

    Standard resistance (check for short):
    Tester Connection
    Condition
    Specified Condition
    2 (ETCS fuse) or A21-3 (+BM) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reinstall the ETCS fuse.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ETCS FUSE - BATTERY)


← P2111 Throttle Actuator Control System - Stuck Open (+ P2112) (from Nov 2006)P2119 Throttle Actuator Control Throttle Body Range / Performance (from Nov 2006) →