P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit
Diagnostic trouble codes · Vehicles built from Nov 2006
Also covers:
- P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input
- P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input
- P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit
- P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input
- P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input
- P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation
DESCRIPTION
- HINT:
- These DTCs relate to the Accelerator Pedal Position (APP) sensor.
- This ETCS (Electronic Throttle Control System) does not use a throttle cable.
- These DTCs relate to the Accelerator Pedal Position (APP) sensor.
The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.


| DTC No. |
DTC Detection Condition |
Trouble Area |
| P2120 |
VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) |
|
| P2122 |
VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal depressed (1 trip detection logic) |
|
| P2123 |
VPA 4.8 V or more for 2.0 seconds or more (1 trip detection logic) |
|
| P2125 |
VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) |
|
| P2127 |
VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal depressed (1 trip detection logic) |
|
| P2128 |
Following conditions (a) and (b) met for 2.0 seconds or more (1 trip detection logic): (a) VPA2 4.8 V or more (b) VPA between 0.4 V and 3.45 V |
|
| P2138 |
Either of following conditions (a) or (b) met for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA and VPA2 0.02 V or less (b) VPA 0.4 V or less and VPA2 1.2 V or less |
|
- HINT:
- When any of these DTCs are set, check the accelerator pedal position sensor voltage by selecting the following menu items on an intelligent tester: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.
Trouble Area
Accelerator Position No. 1
When AP Released
Accelerator Position No. 2
When AP Released
Accelerator Position No. 1
When AP Depressed
Accelerator Position No. 2
When AP Depressed
VCP circuit open
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
Open or ground short in VPA circuit
0 to 0.2 V
1.2 to 2.0 V
0 to 0.2 V
3.4 to 5.0 V
Open or ground short in VPA2 circuit
0.5 to 1.1 V
0 to 0.2 V
2.5 to 4.5 V
0 to 0.2 V
EPA circuit open
4.5 to 5.0 V
4.5 to 5.0 V
4.5 to 5.0 V
4.5 to 5.0 V
Normal condition
0.5 to 1.1 V
1.2 to 2.0 V
2.5 to 4.5 V
3.4 to 5.0 V
- HINT:
- AP denotes Accelerator Pedal.
FAIL-SAFE
When any of DTCs P2120, P2121, P2122, P2123, P2125, P2127, P2128 and P2138 are set, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM uses the remaining circuit to calculate the accelerator pedal position to allow the vehicle to continue driving. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles. Fail-safe mode continues until a pass condition is detected, and the ignition switch is turned off.WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using an intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION NO. 1 AND ACCELERATOR POSITION NO. 2) |
Connect an intelligent tester to the DLC3.

Turn the ignition switch on (IG).
Turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.
Read the value.
- Standard voltage:
Accelerator Pedal Operation
Accelerator Position No. 1
Accelerator Position No. 2
Released
0.5 to 1.1 V
1.2 to 2.0 V
Depressed
2.5 to 4.5 V
3.4 to 5.0 V
|
|
||||
| OK | ||
| ||
| 2. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
Disconnect the accelerator pedal position sensor connector.

Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance (Check for open):
Tester Connection
Condition
Specified Condition
A20-6 (VPA) - A21-55 (VPA)
Always
Below 1 Ω
A20-5 (EPA) - A21-59 (EPA)
Always
Below 1 Ω
A20-4 (VCPA) - A21-57 (VCPA)
Always
Below 1 Ω
A20-3 (VPA2) - A21-56 (VPA2)
Always
Below 1 Ω
A20-2 (EPA2) - A21-60 (EPA2)
Always
Below 1 Ω
A20-1 (VCP2) - A21-58 (VCP2)
Always
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Condition
Specified Condition
A21-6 (VPA) or A21-55 (VPA) - Body ground
Always
10 kΩ or higher
A21-5 (EPA) or A21-59 (EPA) - Body ground
Always
10 kΩ or higher
A20-4 (VCPA) or A21-57 (VCPA) - Body ground
Always
10 kΩ or higher
A21-3 (VPA2) or A21-56 (VPA2) - Body ground
Always
10 kΩ or higher
A21-2 (EPA2) or A21-60 (EPA2) - Body ground
Always
10 kΩ or higher
A20-1 (VCP2) or A21-58 (VCP2) - Body ground
Always
10 kΩ or higher
Reconnect the accelerator pedal position sensor connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 3. INSPECT ECM (VCPA AND VCP2 VOLTAGE) |
Disconnect the accelerator pedal position sensor connector.

Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Switch Condition
Specified Condition
A20-4 (VCPA) - A20-5 (EPA)
Ignition switch on (IG)
4.5 to 5.5 V
A20-1 (VCP2) - A20-2 (EPA2)
Ignition switch on (IG)
4.5 to 5.5 V
Reconnect the accelerator pedal position sensor connector.
|
|
||||
| OK | |
| 4. REPLACE ACCELERATOR PEDAL ASSEMBLY |
| NEXT | |
| 5. CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTC) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC / Clear.
Clear DTCs.
Allow the engine to idle for 15 seconds or more.
Fully depress and release the accelerator pedal several times quickly.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
- Result:
Result
Proceed to
P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138
A
No output
B
|
|
||||
| A | ||
| ||
