2005-2008 Yaris · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Nov 2006

NOTICE:
Always use "TORX" socket wrench E10 when removing the rear seat.


1. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY

  1. B114569E01
    Remove the 2 package tray trim suspenders.

  1. Remove the 5 pieces of hook tape.

  1. Disengage the 2 claws and remove the package tray trim.


2. REMOVE DECK BOARD SUB-ASSEMBLY

  1. B106371
    Release the 2 knobs and remove the deck board.


3. REMOVE SPARE WHEEL COVER ASSEMBLY

  1. B119913
    Remove the spare wheel cover.


4. REMOVE DECK FLOOR BOX

  1. B106373
    Release the 2 knobs and remove the deck floor box.


5. REMOVE REAR NO. 1 SEAT LEG COVER

  1. B126919E01
    Disengage the 4 claws in the sequence shown in the illustration and remove the No. 1 rear seat leg cover.


6. REMOVE REAR NO. 2 SEAT LEG COVER

  1. B126921E01
    Disengage the 3 claws in the sequence shown in the illustration and remove the No. 1 rear seat leg cover.


7. REMOVE REAR SEAT ASSEMBLY (for LH Side)

  1. B114740
    Using "Torx" socket wrench E10, remove the 3 bolts and pull up the rear seat cushion.

  1. B117760
    Using "Torx" socket wrench E10, remove the 4 bolts and the rear seat.


8. REMOVE REAR FLOOR SERVICE HOLE COVER

A118713
  1. Remove the clip from the floor carpet.

  1. A118728
    Remove the rear floor service hole cover.

  1. A119173
    Disconnect the fuel pump connector.


9. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)

10. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

11. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

A119169
  1. Widen the tip of the tube joint clip and pull out the clip.

  1. Pull out the fuel tank main tube to disconnect it.

    NOTICE:
    1. Keep the O-ring free of foreign matter, as it becomes contaminated easily.
    2. Do not use any tools in this procedure.
    3. Do not forcefully bend or twist the tube.
    4. Put the tube in a plastic bag to prevent damage and contamination.
    5. If the fuel suction plate and tube are stuck together, pinch the tube and turn it carefully to disconnect it.
    6. Do not damage any clips. If a clip is damaged, replace it.


12. DISCONNECT NO. 2 FUEL EMISSION TUBE

A115476
  1. Loosen the clamp and disconnect the No. 2 fuel emission tube.


13. DISCONNECT NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

A115477
  1. Disconnect the No. 1 canister outlet hose sub-assembly.


14. REMOVE FUEL PUMP GAUGE RETAINER

A119171E01
  1. Using SST, remove the fuel pump gauge retainer.

    SST
    09808-14020   (09808-01410, 09808-01420, 09808-01430)

    HINT:
    Align the claws of the fuel pump gauge retainer with the tips of SST.


15. REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

A118739
  1. Remove the fuel suction with pump and gauge tube assembly.

    NOTICE:
    Do not bend the arm of the sender gauge.

  1. A118738
    Remove the fuel suction tube gasket from the fuel tank.


16. DRAIN FUEL

17. REMOVE NO. 4 FRONT FLOOR HEAT INSULATOR
  1. Remove the 2 nuts and remove the No. 4 front floor heat insulator.


18. REMOVE FUEL TANK COVER VENT CASE SUB-ASSEMBLY
  1. Remove the bolt and clip and remove the fuel tank cover vent case sub-assembly.


19. DISCONNECT FUEL TANK BREATHER HOSE

A118741
  1. Loosen the clamp bolt and disconnect the fuel tank breather hose.


20. DISCONNECT FUEL TANK TO FILLER PIPE HOSE

A118742
  1. Loosen the clamp and disconnect the fuel tank to filler pipe hose.


21. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

A109384E01
  1. Release the lock as shown in the illustration, then pull and remove the fuel tank main tube.

    NOTICE:
    1. Remove any dirt and foreign matter from the clip before performing this work.
    2. Avoid any scratches and foreign matter on the parts when disconnecting, as the quick connector has the O-ring that seals the plug.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected parts by covering them with a plastic bag.
    6. If the connector and pipe are stuck, disconnect the nylon tube by turning it by hand.


22. DISCONNECT NO. 2 FUEL EMISSION TUBE

A119220
  1. Loosen the clamp and disconnect the No. 2 fuel emission tube.


23. REMOVE FUEL TANK ASSEMBLY

A105615
  1. Set a transmission jack under the fuel tank.

  1. Remove the 4 bolts and the fuel tank.


24. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

A125130
  1. Remove the fuel tank main tube from the fuel tank.


25. REMOVE NO. 2 FUEL EMISSION TUBE

A118747
  1. Remove the No. 2 fuel emission tube from the fuel tank.


26. REMOVE FUEL TANK BREATHER TUBE

A118754
  1. Loosen the clamp bolt and remove the fuel tank breather tube.

← COMPONENTS (from Nov 2006)INSTALLATION (from Nov 2006) →