INSTALLATION
Removal / installation · Vehicles built from Nov 2006
- NOTICE:
- Always use "TORX" socket wrench E10 when installing the rear seat.
| 1. INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY |
![]() ![]() |
Install a new gasket onto the fuel tank.
Align the protrusion of the fuel pump with the cutout of the fuel tank and install the fuel suction with pump and gauge tube assembly.

- NOTICE:
- Do not bend the arm of the sender gauge.
| 2. INSTALL FUEL PUMP GAUGE RETAINER |
![]() ![]() |
Turn the retainer 180° clockwise by hand from the screw starting point and further turn it 360° clockwise using SST to align the claw of the retainer with the matchmark on the fuel tank.
- SST
- 09808-14020
(09808-01410, 09808-01420, 09808-01430)
- NOTICE:
- Replace the fuel pump gauge retainer with a new one if not turned 180° clockwise by hand.
- Part No. 77144-52040
- HINT:
- Align the claws of the fuel pump gauge retainer with the tips of SST.
- At the point where the retainer is turned 90° from the start of the thread, push the retainer in from the opposite side to the start of the thread. Check that the thread of the retainer is properly engaged with that on the fuel tank.
- Align the claws of the fuel pump gauge retainer with the tips of SST.
| 3. CONNECT NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY |
![]() ![]() |
Connect the No. 1 canister outlet hose sub-assembly.
| 4. CONNECT NO. 2 FUEL EMISSION TUBE |
![]() ![]() |
Connect the No. 2 fuel emission tube.
| 5. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY |
![]() ![]() |
Insert the fuel tank main tube sub-assembly.
Install the tube joint clip.
- NOTICE:
- Check that there are no scratches or foreign matter on the connecting parts.
- Check that the fuel tube joint is inserted securely.
- Check that the fuel tube joint clip is on the collar of the fuel tube joint.
- After installing the tube joint clip, check that the fuel tube joint has not been pulled off.
- Do not damage the clip. If a clip is damaged, replace it.
- Check that there are no scratches or foreign matter on the connecting parts.
| 6. INSTALL REAR FLOOR SERVICE HOLE COVER |
![]() ![]() |
Connect the fuel pump connector.
Install the rear floor service hole cover with new butyl tape.

Install the floor carpet with the clip.
| 7. INSTALL REAR SEAT ASSEMBLY (for LH Side) |
Insert the 2 location pins through the 2 body holes and install the rear seat.

Using "Torx" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.
- Torque:
- 37 N*m{ 375 kgf*cm , 27 ft.*lbf }
Install the rear seat cushion.

Using "Torx" socket wrench E10, install the 3 bolts in the sequence shown in the illustration.
- Torque:
- 37 N*m{ 375 kgf*cm , 27 ft.*lbf }
| 8. INSTALL REAR NO. 2 SEAT LEG COVER |
Engage the 3 claws and install the No. 2 rear seat leg cover.

| 9. INSTALL REAR NO. 1 SEAT LEG COVER |
Engage the 4 claws and install the No. 1 rear seat leg cover.

| 10. INSTALL DECK FLOOR BOX |
Install the deck floor box and lock the 2 knobs.

| 11. INSTALL SPARE WHEEL COVER ASSEMBLY |
Install the spare wheel cover.

| 12. INSTALL DECK BOARD SUB-ASSEMBLY |
Set the deck board and lock the 2 knobs.

| 13. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY |
Engage the 2 claws and install the package tray trim panel.

Install the 5 pieces of hook tape.
Install the 2 package tray trim suspenders.
| 14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
| 15. INSPECT FOR FUEL LEAK |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and the intelligent tester main switch ON.
- NOTICE:
- Do not start the engine.
Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump /Speed.
Check that there is no fuel leakage anywhere in the fuel system after doing maintenance.






