2005-2008 Yaris · Service Manual ENGINE

P0617 Starter Relay Circuit High

Diagnostic trouble codes · Vehicles built from Nov 2005

DESCRIPTION

The cranking holding control system keeps energizing the starter relay from when the ECM detects the starter signal (STSW signal) from the ignition switch or the main body ECU until the ECM performs a judgement of "Engine started". Furthermore, the ECM outputs an accessory cut signal (ACCR signal) to the ACC cut relay during cranking to prevent flickering of the combination meter, clock, audio system, and so on.
When the ECM detects the STSW signal, the ECM outputs the starter relay drive signal (STAR signal) to the starter relay through the clutch start switch or park/neutral position switch, and then, the engine is cranked. When the ECM receives a stable engine speed signal (NE signal), more specifically, when the NE signal reaches a predetermined value, the ECM stops outputting the STAR signal. Also, the ECM monitors the starter relay operating conditions based on the STA terminal voltage status.
A103821E16
While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM.
If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.
DTC No.
DTC Detection Conditions
Trouble Areas
P0617
When conditions (a), (b) and (c) met for 20 seconds (1 trip detection logic):
  1. (a) Vehicle speed more than 20 km/h (12.4 mph)
  2. (b) Engine speed more than 1,000 rpm
  3. (c) STA signal ON
  1. Park/Neutral Position (PNP) switch (MMT*)
  2. Clutch start switch (M/T*)
  3. Starter relay circuit
  4. Ignition switch
  5. ECM
*: M/T denotes Manual Transaxle models and MMT denotes Multi-mode Manual Transaxle models

WIRING DIAGRAM

A128481E01
A122549E01

INSPECTION PROCEDURE

HINT:
  1. The following troubleshooting flowchart is based on the premise that the engine is cranked normally.
    If the engine will not crank, proceed to the problem symptoms table (Click here).
  2. Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STARTER RELAY)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Active test / Activate the Starter Relay.

  1. Read the value displayed on the tester when the ignition switch is on (IG) and the engine starts.

    Result:
    Conditions
    Starter Signal
    Ignition switch on (IG)
    OFF
    Engine start
    ON

    Result:
    Result
    Proceed To
    Within standard range
    A
    Outside standard range (vehicle without entry and start system)
    B
    Outside standard range (vehicle with entry and start system)
    C



B
Go to step 2

C
Go to step 7
A

CHECK FOR INTERMITTENT PROBLEMS

2. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)

  1. A122550E04
    Inspect the clutch start switch circuit (for Manual Transaxle models).
    1. Disconnect the A16 clutch start switch assembly connector.

    2. Connect an intelligent tester to the DLC3.

    3. Turn the ignition switch on (IG) and turn the tester on.

    4. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

    5. Read the value displayed on the tester when the ignition switch on (IG).

      Result:
      Starter Signal
      Proceed To
      ON
      A
      OFF
      B

    6. Reconnect the clutch start switch connector.

  1. Inspect the Park/Neutral Position (PNP) switch circuit (for Multi-mode Manual Transaxle models).

    1. Disconnect the A43 PNP switch connector.

    2. Connect an intelligent tester to the DLC3.

    3. Turn the ignition switch on (IG) and turn the tester on.

    4. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

    5. Read the value displayed on the tester when the ignition switch on (IG).

      Result:
      Starter Signal
      Proceed To
      ON
      A
      OFF
      B

    6. Reconnect the PNP switch connector.



B
Go to step 4
A


3. CHECK HARNESS AND CONNECTOR (STA TERMINAL VOLTAGE)
A122539E01
  1. Disconnect the A21 ECM connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminal of the ECM connector and body ground.

    Result:
    Tester Connections
    Specified Conditions
    Proceed To
    STA (A21-48) - Body ground
    9 to 14 V
    NG
    Below 1.5 V
    OK

  1. Reconnect the ECM connector.



OK
REPLACE ECM
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - PNP SWITCH OR CLUTCH START SWITCH - ST RELAY)

4. INSPECT PARK/NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH
A122558E01
  1. Inspect the clutch start switch (for Manual Transaxle models).

    1. Disconnect the A16 clutch start switch connector.

    2. Check the resistance.

      Result:
      Switch Positions
      Tester Connections
      Specified Conditions
      OFF (free)
      1 - 2
      10 kΩ or higher

    3. Reconnect the clutch start switch connector.

  1. Inspect the PNP switch (for Multi-mode Manual Transaxle models).

    1. Disconnect the A43 PNP switch connector.

    2. Check the resistance.

      Result:
      Switch Positions
      Tester Connections
      Specified Conditions
      OFF (free)
      1 - 2
      10 kΩ or higher

    3. Reconnect the PNP switch connector.



OK
Go to step 6
NG


5. REPLACE PARK/NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH

NEXT


6. INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
A122544E01

HINT:
If the vehicle is a multi-mode manual transaxle model, proceed to OK.

  1. Disconnect the D8 ignition switch connector.

  1. Check the resistance.

    Result:
    Tester Connections
    Specified Conditions
    4 (AM1) - 7 (ST2)
    10 kΩ or higher
    5 (AM2) - 7 (ST2)

  1. Reconnect the ignition switch connector.



NG
REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (CLUTCH START SWITCH - IG SWITCH AND ECM, OR PNP SWITCH - ECM)

7. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)

  1. A122550E04
    Inspect the clutch start switch circuit (for Manual Transaxle models).
    1. Disconnect the A16 clutch start switch assembly connector.

    2. Connect an intelligent tester to the DLC3.

    3. Turn the ignition switch on (IG) and turn the tester on.

    4. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

    5. Read the value displayed on the tester when the ignition switch on (IG).

      Result:
      Starter Signal
      Proceed To
      ON
      A
      OFF
      B

    6. Reconnect the clutch start switch connector.

  1. Inspect the Park/Neutral Position (PNP) switch circuit (for Multi-mode Manual Transaxle models).

    1. Disconnect the A43 PNP switch connector.

    2. Connect an intelligent tester to the DLC3.

    3. Turn the ignition switch on (IG) and turn the tester on.

    4. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

    5. Read the value displayed on the tester when the ignition switch on (IG).

      Result:
      Starter Signal
      Proceed To
      ON
      A
      OFF
      B

    6. Reconnect the PNP switch connector.



B
Go to step 9
A


8. CHECK HARNESS AND CONNECTOR (STA TERMINAL VOLTAGE)
A122539E01
  1. Disconnect the A21 ECM connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminal of the ECM connector and body ground.

    Result:
    Tester Connections
    Specified Conditions
    Proceed To
    STA (A21-48) - Body ground
    9 to 14 V
    NG
    Below 1.5 V
    OK

  1. Reconnect the ECM connector.



OK
REPLACE ECM
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - PNP SWITCH OR CLUTCH START SWITCH - ST RELAY)

9. INSPECT PARK/NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH
A122558E01
  1. Inspect the clutch start switch (for Manual Transaxle models).

    1. Disconnect the A16 clutch start switch connector.

    2. Check the resistance.

      Result:
      Switch Positions
      Tester Connections
      Specified Conditions
      OFF (free)
      1 - 2
      10 kΩ or higher

    3. Reconnect the clutch start switch connector.

  1. Inspect the PNP switch (for Multi-mode Manual Transaxle models).

    1. Disconnect the A43 PNP switch connector.

    2. Check the resistance.

      Result:
      Switch Positions
      Tester Connections
      Specified Conditions
      OFF (free)
      1 - 2
      10 kΩ or higher

    3. Reconnect the PNP switch connector.



OK
Go to step 11
NG


10. REPLACE PARK/NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH

NEXT


11. CHECK STARTER CUT RELAY (TERMINAL VOLTAGE)
A122713E02
  1. Remove the ST CUT relay.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminal of the ST CUT relay holder and body ground.

    Result:
    Tester Connections
    Specified Conditions
    Proceed To
    ST CUT relay (D67-3) - Body ground
    9 to 14 V
    A
    ST CUT relay (D67-5) - Body ground
    9 to 14 V
    B

  1. Reinstall the ST CUT relay.



B
Go to step 14
A


12. CHECK HARNESS AND CONNECTOR (ECM - ST CUT RELAY)
A122546E01
  1. Disconnect the C20 ECM connector.

  1. Remove the ST CUT relay.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminal of the ST CUT relay holder and body ground.

    Result:
    Tester Connections
    Specified Conditions
    Proceed To
    ST CUT relay (D67-3) - Body ground
    9 to 14 V
    NG
    Below 1.5 V
    OK

  1. Reconnect the ECM connector.

  1. Reinstall the ST CUT relay.



OK
REPLACE ECM
NG


13. CHECK HARNESS AND CONNECTOR (ECM - MAIN BODY ECU - ST CUT RELAY)
A122547E01
  1. Disconnect the C20 ECM connector.

  1. Disconnect the D66 main body ECU connector.

  1. Remove the ST CUT relay.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminal of the ST CUT relay holder and body ground.

    Result:
    Tester Connections
    Specified Conditions
    Proceed To
    ST CUT relay (D67-3) - Body ground
    9 to 14 V
    NG
    Below 1.5 V
    OK

  1. Reconnect the ECM connector.

  1. Reconnect the main body ECU connector.

  1. Reinstall the ST CUT relay.



OK
REPLACE MAIN BODY ECU
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ST CUT RELAY)
A122548E01
  1. Disconnect the D66 main body ECU connector.

  1. Remove the ST CUT relay.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminal of the ST CUT relay holder and body ground.

    Result:
    Tester Connections
    Specified Conditions
    Proceed To
    ST CUT relay (D67-5) - Body ground
    9 to 14 V
    NG
    Below 1.5 V
    OK

  1. Reconnect the main body ECU connector.

  1. Reinstall the ST CUT relay.



OK
REPLACE MAIN BODY ECU
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR


← P0604 Internal Control Module Random Access Memory (RAM) Error (+ P0606, P0607, P0657) (from Nov 2005)P0724 Brake Switch "B" Circuit High (from Nov 2005) →